Solar Contractor Insurance by State
Tennessee Solar Contractor Insurance
Tennessee’s licensing Board speaks in trades and project values rather than in solar, and the state-level answers on solar sales, the electrical code and workers’ compensation are not yet confirmed.
The license that reaches a Tennessee solar job is, on the evidence of the Tennessee Board for Licensing Contractors’s own pages, a contractor license required before a business contracts, bids included, with subcontractors licensed for electrical, mechanical, plumbing, HVAC or roofing work when they contract directly with a contractor. Those pages do not name solar, and this page does not read that as an exemption. Which electrical code governs the wiring, whether the state sets its own rules for solar sellers and installers, and how workers’ compensation is structured are each not confirmed at the state level.
That is an unusual position for an owner to be in, and it is worth saying plainly what it does and does not mean. A finding that is not confirmed is an open question. It is not a finding that nothing applies. The sections below give the Board’s words where there are any, say what each open question is and whom to put it to, and offer advice for the owner whose name goes on the proposal.
How the policies themselves work for a solar business anywhere is laid out on the solar contractor insurance page and the coverage pages it links to. This page keeps to what is particular to Tennessee, whether your business does rooftop installation, runs panel cleaning and maintenance routes or takes on ground-mount and solar farm construction.
A stack of layers under a Tennessee solar job, read from the top down. At the top is the Board’s contractor license, required before contracting, bidding included, with a project-value threshold; its pages do not name solar. Beneath it is the subcontractor rule: a subcontractor contracting directly with a contractor must be licensed for electrical, mechanical, plumbing, HVAC or roofing work. Next is the limited electrician license, required only where a municipality uses the state fire prevention division for permits or inspections. Below that is the electrical code and the solar sales rules, each not confirmed at the state level. At the bottom is the workers’ compensation structure, also not confirmed at the state level. No figures are shown.
A contractor license page that never names solar
The body that licenses contracting in Tennessee is the Tennessee Board for Licensing Contractors, which licenses contractors, home improvement contractors, limited licensed electricians and limited licensed plumbers. Its contractor license page opens the question this way:
“A contractor’s license is required before contracting, including bidding, offering to engage, or negotiating a price”
Authority: Tenn. Code Ann. Title 62, Chapter 6 (Board for Licensing Contractors law page)
Read the verbs before reading anything else. The license is required before contracting, and the page spells out what counts as contracting: bidding, offering to engage and negotiating a price. For a solar business that moves the moment of decision earlier than the building. The proposal that goes to a customer, the quote that goes to a general contractor and the negotiation over a price all sit inside the sentence, so the question of whether the business holds the license comes up at the bid, not on the day the crew arrives.
The sentence in the Board’s page goes on to tie the requirement to a project-value threshold and to name the roles it covers. This page does not restate the threshold, and an owner should not rely on a figure remembered from another job or another place. As advice, ask the Board for the current threshold and the current list of roles in writing, date the reply and keep it where the estimator can find it. A price on an array that sits near the threshold is exactly the price that needs the answer in hand before it is sent.
Cautions about the source belong beside the quotation. The attribution calls the page an agency summary, not the statute, so the words above describe the law and are not the law itself. And the Board’s license pages that are quoted and cited here do not name solar or photovoltaic work. That is a narrow statement about what those pages say. It is not a statement that solar work is exempt, and it is not a statement that no license applies to it. The Board’s detailed classification list and its rules are not quoted on this page, so whether a classification reaches a photovoltaic array is not confirmed.
The practical result is a question for the Board, and the owner has to ask it. A short list of what to put in the letter:
- Whether a business that bids, installs and services photovoltaic arrays must hold the contractor license, and under which classification the Board would place that scope.
- Whether the answer changes with the project’s value, the customer’s identity or the building the array is attached to.
- Who must hold the license on a given job: the business, a named individual or the contractor that hires you.
- Whether the Board treats a crew that only mounts hardware differently from a crew that completes the electrical connection.
Licensing by trade, and what that asks of a solar bid
Some licensing schemes carve out a credential written for solar. The Tennessee pages quoted here do not. They speak in trades. The Board’s page makes that plain in its statement about subcontractors:
“Subcontractors must be licensed when contracting directly with a contractor, not the owner, to perform electrical, mechanical, plumbing, HVAC, or roofing work”
Notice the structure of the sentence. The duty to be licensed turns on whom the business contracts with. A subcontractor that contracts directly with a contractor, rather than with the owner, falls under the sentence when the work falls in a listed trade. A business that contracts with the owner falls under the earlier sentence about contractors instead. The same company can stand on either side of that line from project to project, which is why a licensing file for a solar business is a per-job record and not a certificate on the office wall.
The trades the sentence lists are the trades an array touches. The wiring is electrical work. The attachment of racking to a roof surface brings roofing into the picture. A ground-mount project may involve work that none of the listed trades describes. Whether the Board places any part of a photovoltaic scope within a listed trade is not confirmed on this page, and it would be a mistake to answer the question from the list alone. The point of reading the list is to know which questions to ask, not to supply the answers.
As advice, sort every job at intake by position and by trade before the proposal is written:
- Who signs with whom. Record whether the business will contract with the owner or with another contractor. The Board’s page treats those positions differently, and the answer determines which sentence you are reading.
- Which trades the scope touches. Write down, job by job, whether the crew will do roofing attachments, electrical connections or each kind of work, and who on the job answers for each.
- Who holds which license. If you subcontract the tie-in, ask the electrician for the license and the certificate of insurance together and file them with the subcontract. If your own crew makes the connection, tell your agent what license backs it, so the program rests on accurate facts.
- What the Board said. Keep its written replies with the proposal. A licensing position given on the telephone and forgotten by the next week is no defense when a customer or a general contractor asks what you relied on.
How a liability policy treats the electricians and roofers a solar business brings in, and damage a crew causes on a roof or in a building, is set out on the general liability page. The trade your scope falls in matters to that policy as well as to the license.
Permits issued by the state in some municipalities, and a wiring code not confirmed
The Board has a separate license for smaller electrical jobs, and its page on that license draws a line by municipality rather than by the kind of building:
“The Limited Licensed Electrician (LLE) license is only required by electricians performing work in a municipality utilizing the Division of Fire Prevention for permits or inspections”
Read what the sentence establishes. Some municipalities use the state fire prevention division for permits or inspections, and in those places the limited electrician license is required of electricians doing work. The line is drawn at the municipality, so the same job could sit on either side of it depending on where the array goes up. The sentence continues with a limit on the jobs the license covers; this page does not restate it. Whether a photovoltaic tie-in falls inside the scope of that license is not confirmed here, and the license is described by the Board in terms of electricians doing the work, not contracting businesses.
That sentence also tells an owner something useful about the permit route. In a municipality that uses the state division, the office reviewing the work is a state office. For a municipality that does not, this page does not say which office reviews it, and the owner should ask rather than assume. As advice, lead with this question on every job in a new place: which office issues the electrical permit here, and which office inspects the finished work?
The electrical code is the point where that question turns into a design instruction. Which edition of the National Electrical Code governs a Tennessee array, whether the state adopts it for all jobs or leaves adoption to the local government, and whether any amendment touches the photovoltaic article are not confirmed at the state level on this page. The accurate statement is that the edition is unknown here. It is not that the state has no code, and it is not that a particular edition applies.
Because the edition is open, treat it as a question for the people who will inspect the work:
- Ask the permitting office for the address which edition its inspectors apply, and whether any local amendment changes the photovoltaic article.
- Where the municipality uses the state fire prevention division, ask that division the same question and ask for the answer in writing.
- Give the edition to the designer before the drawings are final. A design that leans on a newer provision can fail inspection under an older code, and a design written to an older edition can miss a requirement a newer code added.
- Keep the drawings, the equipment listings and the inspector’s sign-off together. A wiring fault traced back to the work after the job is done is judged against what the code required on the day it was built.
A fault in completed wiring that comes to light later is a general liability matter, and a clear file showing the code you built to helps whoever has to answer the claim.
What a proposal should carry while a solar sales rule is unconfirmed
Whether Tennessee has written rules for the businesses that sell, finance or install solar systems for customers is not confirmed at the state level on this page. That covers the kind of rule some places impose, such as a required disclosure, a seller registration or a qualification for installers, and it covers the question of whether any such rule reaches only homes or reaches commercial buyers as well. None of that is established here, and it would be wrong to say it does not exist. The finding is an open question, and the owner should treat it so.
The practical response is to write the proposal as though a skeptical customer, and perhaps a regulator, will read it later. Whether or not a solar-specific rule turns up, the same habits protect the business:
- State how the output estimate was produced and what it assumes about shading, orientation and equipment, so a shortfall traces to a stated assumption rather than to a vague promise.
- List every cost the customer will bear, including any that arrive after installation, and say in plain words who does what: what your business does, what the customer does and what a utility or another party does.
- Say who holds the license behind the work and what the Board’s position was, if you asked it, as described above.
- Give the customer a signed copy of what was agreed, and keep a dated note of any verbal claim a salesperson made at the door or on the telephone.
- Train the sales team on a point it may not expect: a signature and a promise raise questions of their own, whatever the license says about the work.
As advice, put the unconfirmed question to a lawyer who knows the state’s consumer sales law before the proposal template goes out, and to the Board where the question is about who may sell and who may install. The sooner the business knows whether a rule applies, the cheaper it is to write the template right.
If a customer relies on an estimate that turns out wrong and nothing is damaged, the claim that follows is a professional liability question rather than a general liability claim, and that page sets out how such a policy responds. Nothing here describes a Tennessee rule about solar sales; the state-level finding is only that a rule for solar sellers and installers is not confirmed.
A comp structure still to be confirmed, and what to settle before the crew starts
How workers’ compensation is structured for a Tennessee employer is not confirmed at the state level on this page. That means this page does not say who must carry it, from whom it may be bought, what a covered employer must show, or what happens to an employer that goes without. It does not describe a state fund, and it does not rule that out. It does not name an insurer, and it does not say that private insurers write the coverage. Each of those is a question for a person who can answer it for your payroll.
The cost of leaving it open is real, because a crew member hurt on the job is the event that tests the arrangement. A roofer who falls from a ladder is a claim whose handling depends entirely on how comp was placed before the day. As advice, settle the following with the right people before anyone joins the payroll:
- Ask your agent how workers’ compensation is placed for a Tennessee payroll, from whom, and what the application will ask about your crews and subcontractors.
- Ask the state’s insurance regulator what applies to an employer of your size and kind, and ask it to point you to the statute or rule that says so.
- Ask the Board whether proof of coverage is part of any license application you file, since a license and a payroll can meet at that desk.
- Settle, for each job, who is your employee and who is a subcontractor, and collect a certificate of coverage from every subcontractor before its people set foot on an array.
Classification and audit are policy questions that hold in any state. How roof crews, ground crews and service technicians are classified, how subcontractors are treated at audit and how a policy follows a crew that travels are set out on the workers’ compensation page. Read it with the knowledge that the state-level structure is the piece still to be confirmed. Nothing on this page reaches past Tennessee’s border; for a job in a neighboring state, check that state’s rules.
Tennessee’s record names only the Board for Licensing Contractors, and the rest of this page is thin. One federal source that needs no state reading is OSHA’s Fall Prevention Campaign, on falls in construction.
The licensing Board, and the offices that hold the open answers
The licensing body behind this page is the Tennessee Board for Licensing Contractors, which licenses contractors, home improvement contractors, limited licensed electricians and limited licensed plumbers. It is the office to ask the licensing questions in the sections above: the project-value threshold, the classification for a photovoltaic scope, who must hold the license on a job and the scope of the limited electrician license.
Other offices hold the remaining answers, and the owner should know which is which before calling:
- The state fire prevention division, which the Board’s page names as the permit and inspection office in some municipalities. Ask it about permits, inspections and the code its inspectors apply where it serves the municipality.
- The local building or permitting department for the address of the job. In a municipality that does not use the state division, this is where the permit, the inspection and the code edition are settled.
- The state’s insurance regulator, for the questions about how workers’ compensation applies to an employer and for the license standing of the agencies that place your program.
Any agency that sells you a policy, ours among them, can be looked up on NIPR.com. Ask the agency quoting your program for its license details and check them there before you sign.
The Tennessee counties inside each metro card, including metros that cross a state line
The cards below show the largest metropolitan areas with a principal city in Tennessee, as the U.S. Census Bureau delineates them, and the Tennessee counties inside each.
Nashville-Davidson--Murfreesboro--Franklin, TN
Made up of Cannon County, Cheatham County, Davidson County, Dickson County, Hickman County, Macon County, Maury County, Robertson County, Rutherford County, Smith County, Sumner County, Trousdale County, Williamson County and Wilson County.
Memphis, TN-MS-AR
Part of this metro lies outside Tennessee; this card lists its Tennessee counties only: Fayette County, Shelby County and Tipton County.
Knoxville, TN
Made up of Anderson County, Blount County, Campbell County, Grainger County, Knox County, Loudon County, Morgan County, Roane County and Union County.
Chattanooga, TN-GA
Part of this metro lies outside Tennessee; this card lists its Tennessee counties only: Hamilton County, Marion County and Sequatchie County.
Clarksville, TN-KY
Part of this metro lies outside Tennessee; this card lists its Tennessee counties only: Montgomery County and Stewart County.
Kingsport-Bristol, TN-VA
Part of this metro lies outside Tennessee; this card lists its Tennessee counties only: Hawkins County and Sullivan County.
The Board’s license applies to the business wherever it contracts, but the permit route and the inspecting office are set by the municipality where the array goes up, and a metro area spans many of them. A metro on the map is therefore a set of separate permit offices, not a uniform market. As advice, log the county and the municipality for every job you price, ask that place which office issues the electrical permit before the proposal goes out, and do not assume that what a city told you about its inspectors holds in the next town over.
Coverage pages that answer the duties the Board’s pages do state
The findings above say where Tennessee’s rules sit and where they are still to be confirmed. The policies that answer for the work are the ones a solar business carries wherever it works, and each has its own page:
- The licensing question, the electricians and roofers you bring in, and finished wiring all point to general liability, which also takes up damage to the roof or building under the array.
- Estimates and designs a customer relied on, in a state where a solar sales rule is not confirmed, point to professional liability.
- The comp structure left to be confirmed points to workers’ compensation, which sets out classification, audit and subcontractor certificates.
- Trucks and trailers that carry modules and racking between the yard and the job point to commercial auto.
- Meters, lifts and stock on the way to a job point to tools and equipment.
- Contracts that ask for limits above the primary layer point to umbrella liability.
Which of those weigh heaviest depends on the work, and the pages on rooftop installation, panel cleaning and maintenance and ground-mount and solar farm construction take each kind of work on its own terms. When you are ready to put the pieces together for Tennessee jobs, a quote request is the place to start.
State rules decide who may do the work and how; the policies decide who pays when something goes wrong.
- A license, registration or certification is a requirement of the state, not insurance.
- License to install is not confirmed at the state level on this page.
- Solar sales and installer rules is not confirmed at the state level on this page.
- Electrical code is not confirmed at the state level on this page.
- Workers’ compensation is not confirmed at the state level on this page.
A panel for Tennessee in rows. Each row sets a requirement of the state beside the exposure that requirement leaves open and the coverage line that answers it. License to install: Not confirmed at the state level. No connector is drawn for this row. Solar sales and installer rules: Not confirmed at the state level. No connector is drawn for this row. Electrical code: Not confirmed at the state level. No connector is drawn for this row. Workers’ compensation: Not confirmed at the state level. No connector is drawn for this row. Notes: A license, registration or certification is a requirement of the state, not insurance. License to install is not confirmed at the state level on this page. Solar sales and installer rules is not confirmed at the state level on this page. Electrical code is not confirmed at the state level on this page. Workers’ compensation is not confirmed at the state level on this page. The conclusion reads: State rules decide who may do the work and how; the policies decide who pays when something goes wrong. No figures are shown.
Nearby states we also write
Tennessee coverage, services and state offices
What we insure
Coverage lines
Outside authorities
Tennessee solar contractor insurance questions
The Board’s license pages never mention solar. Can our array crew bid without a contractor license?
Do not read silence as permission. The Tennessee Board for Licensing Contractors says a contractor license is required before contracting, bidding included, and its pages that are quoted here do not name solar. That is a statement about the pages, not an exemption. Put the scope of the bid to the Board in writing and keep the reply with the proposal.
A general contractor hired us to set the array on its building. Does the subcontractor rule reach us?
It may. The Board’s page says a subcontractor must be licensed when contracting directly with a contractor, not the owner, for electrical, mechanical, plumbing, HVAC or roofing work. Whether your scope counts as a listed trade is not confirmed on this page, so ask the Board before you sign the subcontract, and file its answer with the contract.
Our city sends electrical permits to the state. Does our wiring then call for the limited electrician license?
The Board ties that license to electricians working in a municipality that uses the state fire prevention division for permits or inspections. Whether your wiring work falls in the license’s scope is not confirmed here. Ask the Board about the scope and the city about which office issues its permits, then settle who on your crew holds what.
Nobody has handed us an electrical code edition for Tennessee jobs. Whom do we ask before the drawings are final?
Ask the permitting office for the address, because the edition is not confirmed at the state level on this page. Where the municipality uses the state fire prevention division, ask that division too. Get the edition, any local amendments and any rule on the photovoltaic article in writing, and give the answer to your designer before the sheets are issued.
Our reps want to know what Tennessee requires them to hand a customer before signing. What do we tell them?
Tell them that a state rulebook written for solar sellers is not confirmed, which is not the same as there being no rule. Until it is settled, have reps work from the proposal habits on this page: how the estimate was built, every cost, who does what, and a signed copy for the customer. Review the script with counsel who knows the state’s consumer sales law.
We are adding crew this season. Where do we learn what Tennessee requires for their workers’ compensation?
The structure is not confirmed at the state level on this page, so do not assume how it works. Ask your agent how comp is placed for a Tennessee payroll and ask the state insurance regulator what applies to an employer your size. Settle it before anyone climbs a ladder, then collect certificates from every subcontractor.
Who stands behind the agency pricing our Tennessee program, and how do we check its license?
An insurance agency’s license, ours among them, can be looked up on NIPR.com. Ask any agency that quotes your program for its license details and check them there before you sign. Because the comp structure is not confirmed here, ask the agency to explain in writing where your comp would be placed.
This page describes insurance for solar contractors operating in this state. It is general information, not legal advice and not a statement of coverage. Licensing, interconnection and code requirements change; verify current requirements with the agency named before relying on them.
Get a quote for your Tennessee solar contracting business
Tell us which Tennessee metros you bid in, whether you contract with owners or with other contractors, and how your crew is paid, and we will build the program on those answers.