Solar Contractor Insurance by State

Alabama Solar Contractor Insurance

Alabama licenses the wiring through a state board or the county or municipality, lists only certain buildings under its State Building Code, has not confirmed its own solar seller rules, and requires workers’ compensation without a state fund.

Installers in fall-protection harnesses and safety lines work among solar panels on a low-slope metal roof, one carrying a hand tool.

Alabama licenses electrical contracting through the Alabama Board of Electrical Contractors or through the county or municipality where the work is performed, and because the statute reaches anyone who bids, installs, maintains, alters or repairs electric wiring devices or equipment, that license reaches an array’s wiring even though neither the statute nor the Board’s rules print the word solar. The State Building Code lists the National Electrical Code but, by its own words, applies only to certain State buildings, schools, hotels and moving picture theaters. Whether the state sets its own consumer rules for solar sellers and installers is not confirmed at the state level. Workers’ compensation is required by law, and the employer chooses how to insure it, with no state fund described.

Those answers come with edges that matter to a bid: a home builders board’s advisory opinion on residential installs, a general contractors board that licenses above a statutory threshold, and a residential code that modifies the solar roof provision for dwellings. The sections below take each finding in turn, with the source’s own words where they matter and advice for the owner.

How the policies themselves work for a solar business anywhere is laid out on the solar contractor insurance page and the coverage pages it links to. This page keeps to what is particular to Alabama, whether your business does rooftop installation, runs panel cleaning and maintenance routes or takes on ground-mount and solar farm construction.

How far Alabama’s wiring statute carries a solar job, and where the narrower layers take over: the home opinion, the short list of buildings, the open seller question and the crew’s comp.

A waterfall in which each step takes what the step above leaves for the next layer to answer. At the top, the electrical contracting statute reaches anyone who bids, installs, maintains, alters or repairs wiring devices or equipment, and never names solar. Below it, a license from the Board of Electrical Contractors, or from the county or municipality where the work sits, satisfies the statute. Next, for installation on a residence, an advisory opinion from the home builders board points to that board’s unlimited license. Then the State Building Code lists the national electrical code but applies only to the buildings its rule names. Beside that, solar seller and installer rules are not confirmed at the state level. At the bottom, the crew rests on compulsory workers’ compensation, insured or self-insured at the employer’s choice, with no state fund described. No figures are shown.

The Board’s electrical license, or the county’s or the city’s own

Alabama licenses electrical contractors statewide through the Alabama Board of Electrical Contractors, and the Board prints no separate solar license. The statute reaches anyone who bids, installs, maintains, alters or repairs electric wiring devices or equipment, and a license from the county or municipality where the work sits also satisfies it. The electrical contractors statute names no solar work. For solar on homes, the Home Builders Licensure Board has said, in an advisory opinion, that installing solar panels on a residence takes its unlimited license, and that is the license the page’s solar quote names.

A solar contractor in Alabama holds an electrical contractor license from the Alabama Board of Electrical Contractors, or a license from the county or municipality where the job sits, before it bids or installs wiring and equipment. A firm that installs panels on homes also answers to the Home Builders Licensure Board, and a project that reaches the statutory dollar threshold of the Alabama Licensing Board for General Contractors needs that Board’s license.

Authority: Code of Alabama 34-36-3; 34-36-13; 34-14A-2; Ala. Admin. Code 303-X-1 through 303-X-5; 230-X-1

The statute begins by defining the work it licenses. Electrical contracting is, in its words:

“Any job or project in the State of Alabama wherein the electrical contractor proposes to bid, install, maintain, alter, or repair any electric wiring devices or equipment.”

Notice the shape of that definition. It turns on wiring devices and equipment, so on a solar job the license attaches to the wiring, the connections and the tie-in. The statute does not carve out a solar scope, and the Board’s rules do not either. The bar on working without a license reads:

“No person shall engage in the electrical contracting business or perform work as a master or journeyman electrician unless such person shall have received a license from the board or from the county or municipality where the electrical contracting work is being performed”

The sentence names a license from the Board and a license from the county or municipality where the work is performed, and either satisfies it. For a firm that works across county lines, the statute adds a rule for the Board’s statewide license:

“any person who holds a valid statewide license issued by the board shall be deemed qualified”

The sentence goes on to say how the holder may work in any county or municipality, under conditions the quoted span cuts off, and the statute keeps the local building permit and business license in place. As advice, read the whole section before relying on it, and ask each building department what it wants in addition to the license.

The same section sets aside a category of work from the chapter:

“To the installation, construction, or maintenance of power systems for the generation and secondary distribution of electric current constructed under the provisions of the National Electrical Safety Code which regulates the safety requirements of utilities.”

That exemption speaks of power systems for generation and secondary distribution built under the utility safety code. Whether a particular array falls inside it is a question for the Board rather than for a brochure, so a firm bidding a large ground-mounted job should ask the Board in writing before it assumes the exemption applies or does not.

Where a state license or a local license will do, record-keeping matters. Note, for each job, which license covers the electrical work and who holds it, and when you subcontract the tie-in, ask the electrician for the license that covers the place where the array sits, along with the certificate of insurance.

How a liability policy treats the electricians and roofers you subcontract, and damage your crews cause on a roof or in a building, is set out on the general liability page.

Home builders and general contractors: where other boards reach the work

The Home Builders Licensure Board is the only public body on this page that speaks to solar by name. The question it was asked, in its words:

“Whether companies and/or individuals need a residential home builders license to install solar panels on residential structures within the state of Alabama.”

Its answer:

“the Board further opines that a company or individual needs an unlimited license issued by the Board to install solar panels upon a residence.”

Read the opinion for what it is. It is advisory, the Board states it may be revoked or modified, and it applies to installation on a residence, so it says nothing about a commercial roof. It rests on the work involving electrical and residential roofing trades and possibly the roof’s structural integrity. As advice, a firm that puts panels on homes should confirm the Board’s current position before the season, hold the license the opinion describes if the Board confirms it, and say in the proposal who holds which license.

The Alabama Licensing Board for General Contractors licenses general contractors and subcontractors above the statutory dollar threshold. A larger commercial or ground-mounted solar job can fall under that license when the contract reaches the threshold, so a firm that builds arrays on open ground should ask the Board how the threshold applies to each contract before it signs. The Board’s classification rules include an electrical specialty and do not name solar. The page on ground-mount and solar farm construction explains how a policy treats that kind of work.

The Board has also posted a notice of contractor licensing exemptions for routine maintenance, repair, cleaning and facility support services, which take effect on the date the notice gives. A panel cleaning or service company should read that notice and ask the Board how it applies to its routes before it bids. The panel cleaning and maintenance page covers how a policy treats a crew on a roof.

Solar seller and installer duties: not confirmed at the state level

Whether Alabama sets its own consumer rules for solar sellers, installers or financiers beyond the licenses counted under the license axis is not confirmed at the state level.

The Public Service Commission’s annual report describes a distributed generation provision of an energy act that shields the electric utility from liability for interconnection and operation of a customer’s facility; that provision runs to the utility, not to installers or sellers. Whether a statute or rule imposes disclosure, registration or contract duties on solar sellers, installers or financiers is not confirmed.

The only solar-adjacent text on this subject is a liability provision of the Legislature’s alternative and renewable energy act, as the Alabama Public Service Commission quotes it in an annual report:

“no utility shall be liable to any person, group of persons, or legal entity, directly or indirectly, for damage to or loss of property, injury, or death that arises in any way from the interconnection or operation of a distributed generation facility.”

That sentence runs to the electric utility. It shields the utility from liability for damage, injury or death arising from the interconnection or operation of a distributed generation facility. It tells a contractor how the utility is protected, not what the contractor owes. Whether another statute or rule imposes disclosure, registration or contract duties on solar sellers, installers or financiers is the part that is not confirmed at the state level.

That leaves the proposal to do the work a rule might have done. As advice, and not as a requirement the state has adopted, write each proposal so that a customer reading it later finds the answers on the page:

  • The basis of the output estimate. Say how it was produced and what it assumes about shading, orientation and equipment.
  • Every cost the customer will bear. A cost that surfaces after signing is a complaint in the making.
  • Who handles the utility paperwork. The Alabama Public Service Commission regulates electric utilities, including interconnection of customer-owned generation. If your business prepares the interconnection application, the customer is relying on you to get it right.

How a policy treats an estimate or a paperwork error that costs the customer money, where nothing was damaged, is explained on the professional liability page.

A State Building Code with a short list of covered buildings

Alabama’s State Building Code, a rule of the Department of Finance’s Construction Management Division, lists the National Electrical Code among its adopted codes, but by its own words the code applies only to State buildings, schools, hotels and moving picture theaters. A separate residential code adopted by the Energy and Residential Codes Board modifies the International Residential Code’s solar photovoltaic roof provision.

Solar wiring on a State building, school, hotel or theater the rule names is built to the adopted National Electrical Code. For other construction, a contractor confirms with the county or city building department which electrical code edition applies before designing the system.

Authority: Ala. Admin. Code 355-12-1-.01(1)(f); 355-12-1-.04; 305-2-4-.09

The Alabama Department of Finance, Construction Management Division adopts the State Building Code, and its rule lists the national code among the adopted standards. The list item reads:

“2020 - National Electrical Code (NFPA 70)”

Whether that code reaches your job depends on the rule’s applicability section, which opens this way:

“Except as stated in paragraphs (2) and (3), the State Building Code applies only to the following construction in Alabama:”

The list that follows begins with the State’s own construction:

“All buildings and other structures erected or acquired by or on behalf of the State of Alabama or any of its agencies or instrumentalities.”

The rule goes on to name public and large private schoolhouses, hotels above a size limit and moving picture theaters. A rooftop array on a school or a State building is therefore a job the adopted code governs. A private commercial building outside that list is not named by this rule, and the rule does not say that adoption outside its list is left to local government, so the question of which edition applies is a question to put to the county or city building department. The rule also settles what happens when codes disagree:

“In case of conflict between the State Building Code, local codes, the Life Safety Code enforced by the State Fire Marshal, or other codes, the most stringent requirements shall prevail.”

As advice, say in the proposal which code your drawings assume so the customer and the inspector read the same thing.

Dwellings are handled separately. The Alabama Energy and Residential Codes Board adopts the state residential building code and residential energy code, and a rule of that Board modifies the solar photovoltaic roof systems section of the model residential code:

“Panels and modules installed on dwellings with hip roof layouts shall be located in a manner that provides a clear access pathway”

That modification is about where panels sit on a hip roof so that a clear access pathway remains. A crew installing on homes should lay out each hip-roof array with the pathway in mind and confirm with the building department which residential code applies to the permit.

How a liability policy treats a fault in completed wiring that comes to light later is explained on the general liability page.

Comp that is required by law, insured or self-insured at the employer’s choice

Workers’ compensation is required by law in Alabama, and the Department of Workforce says the employer chooses how to insure the liability: a policy bought through an agent from an approved insurer, coverage through a residual market, membership in a group self-insurance fund, or individual self-insurance. The Department’s page describes no state fund.

A solar contractor with employees insures its workers’ compensation through an approved insurer or a residual market arrangement, joins a group self-insurance fund, or qualifies with the Department to self-insure; the Department’s page also describes coverage thresholds for small employers and a carve-out for new detached residential construction.

Authority: Code of Alabama 25-5-8

The Alabama Department of Workforce administers workers’ compensation through its Workers’ Compensation Division, including regulation of self-insurance. Its page on insurance requirements begins with the requirement itself:

“It is required by law.”

It then leaves the method to the employer:

“The manner or method by which you choose to insure your workers' compensation liability is your decision.”

The statute gives the same choice in its own words. An employer subject to the chapter may secure the payment of compensation by

“insuring and keeping insured his or her liability in some insurance corporation, association, organization, insurance association, corporation, or association formed of employers and workers or formed by a group of employers to insure the risks under this chapter”

or an employer who elects not to insure its liability

“shall furnish satisfactory proof to the secretary of his or her financial ability to pay directly compensation in the amount and manner and when due as provided by this chapter”

Neither the section’s routes nor the Department’s page names a state fund as a way to secure compensation. For a solar business, that means a policy placed in the market, a group arrangement or approved self-insurance, chosen before anyone on the payroll climbs a ladder. The Department’s page is an agency summary, so the statute, not the page, governs a close question. The page also describes coverage thresholds for small employers and a carve-out for detached residential construction; as advice, do not assume either applies to your payroll without reading the page and asking your agent.

How crews are classified, how subcontractors are treated at audit and how a policy follows a crew that travels are policy questions rather than Alabama questions, set out on the workers’ compensation page. As advice, settle before the season who on each job is your employee, and collect a certificate from every subcontractor before its people set foot on an array.

Alabama licenses solar electrical work through an electrical license, and the Alabama Board of Electrical Contractors listed below is one body a crew deals with. Separately, OSHA’s Fall Prevention Campaign tells employers to plan the job, provide fall protection and train every worker.

The Alabama bodies that hold each part of this picture

No Alabama body covers everything on this page. The body that licenses the wiring is not the body that adopts the code, and neither is the office that administers workers’ compensation. Each link goes to the body’s own site, and the role beside it is what that body does for this work:

Any agency that sells you a policy, this agency among them, can be looked up on NIPR.com. As advice, keep a short sheet by the bid desk that lists, for each job, which body to ask about the license, the code and the crew’s coverage, and remember that the building and permitting departments of the county or city where the array goes up are part of the picture too.

Alabama’s metros and the counties inside them

The cards below show the largest metropolitan areas with a principal city in Alabama, as the U.S. Census Bureau delineates them, and the Alabama counties inside each.

Birmingham, AL

Made up of Bibb County, Blount County, Chilton County, Jefferson County, St. Clair County, Shelby County and Walker County.

Huntsville, AL

Made up of Limestone County and Madison County.

Mobile, AL

Made up of Mobile County.

Montgomery, AL

Made up of Autauga County, Elmore County, Lowndes County and Montgomery County.

Tuscaloosa, AL

Made up of Greene County, Hale County, Pickens County and Tuscaloosa County.

Daphne-Fairhope-Foley, AL

Made up of Baldwin County.

Because the statute lets a county or municipality license the electrical work, a metro area is a set of separate permitting offices rather than a uniform market. As advice, log the county and the city for every job you price, check that place’s requirements before the proposal goes out, and do not assume that a license good in a metro’s principal city is the license its suburbs will accept.

From these Alabama findings to the policies a solar crew carries

The findings above say where Alabama’s rules sit and where they stop. The policies that answer for the work are the ones a solar business carries wherever it works, and each has its own page:

  • The wiring license, the electricians you bring in and the code behind finished work point to general liability, which also takes up damage to the roof or building under the array.
  • Estimates and designs a customer relied on, in a state where seller and installer duties are not confirmed, point to professional liability.
  • The comp requirement and the employer’s choice of route point to workers’ compensation.

Which of those weigh heaviest depends on the work, and the pages on rooftop installation, panel cleaning and maintenance and ground-mount and solar farm construction take each kind of work on its own terms. When you are ready to put the pieces together for Alabama jobs, a quote request is the place to start.

Alabama: what the state sets for solar contractors, what each rule leaves open, and the coverage page that discusses it.
License to install A Home Builders Licensure Board license reaches solar installation on a residence
Damage to the roof, the building or a neighbor’s property from the installation work General Liability
Solar sales and installer rules Not confirmed at the state level
A design, sizing or output estimate the customer relied on that turns out wrong
Electrical code The state names the National Electrical Code in part; local codes govern the rest
A wiring or tie-in fault traced back to the work after the job is done General Liability
Workers’ compensation Required for covered employers, bought in the open market
A crew member hurt on the job Workers’ Compensation

State rules decide who may do the work and how; the policies decide who pays when something goes wrong.

  • A license, registration or certification is a requirement of the state, not insurance.
  • Solar sales and installer rules is not confirmed at the state level on this page.

A panel for Alabama in rows. Each row sets a requirement of the state beside the exposure that requirement leaves open and the coverage line that answers it. License to install: A Home Builders Licensure Board license reaches solar installation on a residence. It leaves open damage to the roof, the building or a neighbor’s property from the installation work, which General Liability answers. Solar sales and installer rules: Not confirmed at the state level. No connector is drawn for this row. Electrical code: The state names the National Electrical Code in part; local codes govern the rest. It leaves open a wiring or tie-in fault traced back to the work after the job is done, which General Liability answers. Workers’ compensation: Required for covered employers, bought in the open market. It leaves open a crew member hurt on the job, which Workers’ Compensation answers. Notes: A license, registration or certification is a requirement of the state, not insurance. Solar sales and installer rules is not confirmed at the state level on this page. The conclusion reads: State rules decide who may do the work and how; the policies decide who pays when something goes wrong. No figures are shown.

Nearby states we also write

Alabama solar contractor insurance questions

If my county already licenses my electrical work, do I also need the Alabama Board’s license to wire an array?

The statute is satisfied by a license from the Alabama Board of Electrical Contractors or by a license from the county or municipality where the electrical contracting work is performed, so a local license can cover work inside that place. A holder of the Board’s statewide license is deemed qualified in any county or municipality, subject to local permits. Ask the building department which license it will accept before you bid.

Does the home builders board’s solar opinion mean my rooftop crew needs a residential license in Alabama?

For installation on a residence, the Home Builders Licensure Board has opined that a company or individual needs its unlimited license. The opinion is advisory, the Board states it may be revoked or modified, and it speaks only to residences. A firm that installs on homes should confirm the current position with the Board before the season, and a commercial-only firm should keep home work out of its schedule or ask the Board beforehand.

Is there an Alabama statute I can point to for what a solar sales proposal must disclose?

That is not confirmed at the state level. The provision the Alabama Public Service Commission quotes from the Legislature’s energy act shields the electric utility from liability and does not speak to sellers or installers. Until the question is settled, write the proposal as if a customer will read it beside a complaint: the basis of the output estimate, every cost, who files the interconnection paperwork and what the warranty covers.

Does the Alabama State Building Code’s electrical code reach a private commercial rooftop job?

The rule that lists the National Electrical Code applies, by its own words, only to State buildings, schools, hotels above a size limit and moving picture theaters, so a private commercial roof is not named on that list. Where codes conflict, the strictest requirement prevails. Ask the county or city building department which edition it applies before you design, and ask the Alabama Department of Finance, Construction Management Division about any State building job.

How does an Alabama solar business with employees choose where its workers’ compensation comes from?

The Alabama Department of Workforce says the choice is the employer’s: a policy from an approved insurer bought through a licensed agent, a residual market, membership in a group self-insurance fund, or individual self-insurance. The statute lets an employer either insure with an approved insurance corporation or association or prove its financial ability to pay directly. Decide before the crew climbs, and keep the proof on file.

Does the residential code’s access-pathway rule for hip roofs matter to a crew that installs only on homes?

It can. The rule comes from the residential code the Alabama Energy and Residential Codes Board adopts, and it speaks of panels and modules installed on dwellings with hip roof layouts. Lay out each hip-roof array with the clear access pathway in mind, and confirm with the local building department which residential code edition it applies, since a rule can be amended after a design is drawn.

Before an agency places our solar crew’s coverage, how do we look up its Alabama insurance license?

Any agency that sells you a policy, ours among them, can be looked up on NIPR.com. Ask the agency for its license details and check them before you sign. Because the Alabama Department of Workforce lets the employer choose among insurance and self-insurance routes, also ask the agency, in writing, which route it is placing for your payroll.

This page describes insurance for solar contractors operating in this state. It is general information, not legal advice and not a statement of coverage. Licensing, interconnection and code requirements change; verify current requirements with the agency named before relying on them.

Get a quote for your Alabama solar contracting business

Tell us which Alabama counties you work in, whether your jobs sit on homes, commercial roofs or open ground, and how your crew is paid, and we will build a program around those answers.