Solar Contractor Insurance by State

Missouri Solar Contractor Insurance

Missouri offers a statewide electrical contractor license that nobody has to hold, leaves electrical codes and permits to cities and counties, reaches solar sellers through its net metering Act, and makes workers’ compensation compulsory for covered employers.

An installer in a hard hat and work overalls carries a solar panel across a lawn toward a modern house.

Missouri has a statewide electrical contractor license that takes in the wiring side of a solar job, but nobody has to hold it: a city or county that licenses may keep its own license, and the state license must be accepted in place of it. No statewide electrical code stands behind that wiring, because the statutes place adoption of an electrical code with counties and political subdivisions, and the state issues no permits and inspects no work. Solar sellers meet the state through the net metering Act, which puts the sale of a customer’s generation unit under the merchandising practices law, rather than through a law written for solar. Workers’ compensation is compulsory for the employers the law covers, with no state fund selling coverage.

Each of those answers hands a decision to someone else: the contractor decides whether the state credential is worth holding, and the city or county decides what the wiring is built to. The sections below take each finding in turn, with the source’s own words where they matter and advice for the owner.

How the policies themselves work for a solar business anywhere is laid out on the solar contractor insurance page and the coverage pages it links to. This page keeps to what is particular to Missouri, whether your business does rooftop installation, runs panel cleaning and maintenance routes or takes on ground-mount and solar farm construction.

Who decides at each step of a Missouri solar job, from whether to hold the optional state license to the carrier that insures the crew.

A waterfall read from the top down, each step the question the previous answer leaves open. At the top, the contractor decides whether to hold the statewide electrical contractor license, which the state office calls optional and which nobody must hold. Beneath it, the city or county that licenses may keep its own license, but must accept the statewide license in place of it. Then the local building department adopts the electrical code, issues the permit and inspects the work, because the state does none of those. Next, the sale of the equipment falls under the merchandising practices law through the net metering Act, which also authorizes the Attorney General to adopt disclosure rules for sellers. Before the system connects, a qualified professional electrician or engineer certifies the installation to the utility. At the bottom, the crew is covered by workers’ compensation placed with an authorized insurer or the residual market, or carried by the employer on the division’s approval, with no state fund. No figures are shown.

A voluntary state license that every city and county must accept

Missouri offers a statewide electrical contractor license, but holding it is voluntary. The Office of Statewide Electrical Contractors issues a license that every city and county must accept in place of a local electrical contractor license, and the state says the license is optional, not mandatory. No statewide license exists for solar installers as such, and none for general or home improvement contractors.

The license that governs a particular solar job comes from the city or county where it sits. A contractor can hold the state license to work in any jurisdiction without a separate local exam, or rely on a local license where a local license is required; either way the permit comes from the local building department, because the state issues no permits and inspects no work.

Authority: RSMo 324.900; RSMo 324.920; RSMo 324.925; RSMo 64.170

The statute behind the license defines electrical contracting broadly, in terms of the generating equipment a solar array is made of:

“engaging in the business of installing, erecting, or maintaining electrical wiring, fixtures, apparatus, equipment, devices, or components, regardless of voltage, that are used for generation, transmission, and utilization of electricity”

That definition is why a solar job’s wiring falls inside the license’s subject, though the statute never mentions solar there. Whether the contractor must hold the license is a different question, and the Missouri Office of Statewide Electrical Contractors answers it directly:

“The statewide electrical contractor license is optional, not mandatory.”

The statute spells out a place where a contractor can do without it. Its provision on local licensing begins this way, and goes on to say that such a person is not required to hold a statewide license:

“Any person operating as an electrical contractor in a political subdivision that does not require the contractor to hold a local license”

Where a place does license, the statute keeps the local government’s hand free and gives the state license standing in return:

“Political subdivisions shall not be prohibited from establishing their own local electrical contractor's license, but shall recognize a statewide license in lieu of a local license”

Read together, the voluntary license works as a portable alternative. As advice, treat it as a decision about how your crews move rather than about whether they may work: a company that bids across many city and county lines may find a credential every place must accept easier to carry than a separate local license for each, while a company that stays inside a county that licenses may prefer the local license it already holds.

A voluntary license is not a solar license. The state offers no credential written for solar installers as such. How a liability policy treats the electricians you subcontract, and damage your crews cause on a roof or in a building, is set out on the general liability page.

The local layer: city certification and a county’s power to license wiring

Because the state license is optional, the license that governs a particular job can be a local license. The statute on county commissions gives them power over the trade. A county commission may

“adopt regulations licensing persons, firms or corporations other than federal, state or local governments, public utilities and their contractors engaged in the business of electrical wiring or installations”

The City of Springfield shows what a city does with its own authority: the city requires electricians, plumbers, gas fitters and mechanical craftsmen to be tested and certified through its Building Development Services department, with certification tiers from journeyman to master, so a crew wiring a solar job inside the city meets the city’s certification. Its trade certifications page puts the requirement this way:

“Electricians, plumbers, gas fitters, and mechanical craftsmen must be tested and certified to afford competence and knowledge of the codes.”

Notice what these rules are written about. They speak of electrical wiring and electricians, not of solar, so on a solar job the part they reach is the wiring and the tie-in. As advice, decide before the bid who on the job will hold the credential the place asks for, or which licensed electrician your crew will work under, and name that person in the proposal.

Where licensing is set locally, careful record-keeping does the work a statewide credential would:

  • Ask the building or licensing office where the job sits whether it licenses electrical work, whether it will accept the state license in place of its own, and what it wants on file before a permit issues.
  • Keep a file of every license and certification each of your crews and subcontractors holds, with the place that issued it. A city’s credential says nothing about the county around it.
  • When you subcontract the tie-in, ask the electrician which license the place accepts.

A net metering Act that doubles as a rulebook for sellers and installers

Missouri’s Net Metering and Easy Connection Act, RSMo 386.890, puts the sale of a customer’s renewable generation unit under the state’s merchandising practices law, authorizes the Attorney General to adopt rules requiring sellers of those units to make mandatory disclosures, makes a seller or installer who knowingly misrepresents a unit’s safety liable for the resulting damage, and requires a certification from a qualified professional electrician or engineer before the unit is interconnected.

Authority: RSMo 386.890(7)(1); RSMo 386.890(13); RSMo 386.890(17)

The Act is about connecting a customer’s own generation to the grid, not about selling solar by name. It reaches solar through its definition of the renewable resources a customer may generate from, which includes this:

“electrical energy produced from wind, solar thermal sources, hydroelectric sources, photovoltaic cells and panels”

The Act speaks of a customer’s qualified generation unit powered by a renewable resource, which takes in rooftop and ground-mounted solar without being limited to solar or to homes. A solar contractor that sells or installs such a unit answers to the Attorney General under the merchandising practices law for what it says about safety and performance, and a licensed electrician or engineer certifies the installation to the utility before it connects.

The sale of the equipment is where the Act touches a contractor’s sales desk. Its sale provision reads:

“The sale of qualified electric energy generation units to any customer-generator shall be subject to the provisions of sections 407.010 to 407.145 and sections 407.700 to 407.720”

The same provision sends rulemaking to the Missouri Attorney General, in these words:

“The attorney general shall have the authority to promulgate in accordance with the provisions of chapter 536 rules regarding mandatory disclosures of information by sellers of qualified electric energy generation units.”

This page quotes no adopted disclosure rule. The Act says the Attorney General has the authority to adopt such a rule, and its sale provision speaks of any customer-generator without limiting itself to homes.

The Act also puts a liability clause on the people who put the equipment in:

“The seller, installer, or manufacturer of any qualified electric energy generation unit who knowingly misrepresents the safety aspects of a qualified electric generation unit may be held liable for any damages to property or person”

Notice the verb. The clause is about a statement that is knowingly false, which makes the paper trail behind a safety claim more important than the claim itself. The Act also adds a step to the interconnection application that falls on the work your crew does:

“the customer-generator will furnish the retail electric supplier a certification from a qualified professional electrician or engineer that the installation meets the requirements”

Safety statements, handoff papers and the certifying electrician in practice

None of what follows is a rule the state has adopted; it is advice built on the statute’s words quoted above.

  • Safety and performance statements. Every sentence in a proposal or a sales deck that tells a customer how safe a system is, or how it will perform, is a sentence that can be read against the Act’s liability clause. Write what you can support, and keep the support in the job file. A shortfall claim that involves no damage at all is taken up on the professional liability page.
  • Who certifies. The Act calls for a certification from a qualified professional electrician or engineer before the unit connects. Decide at the bid stage whether that person is on your payroll, a subcontractor, or a firm the customer hires, and put the answer in the contract so the interconnection date does not wait on a signature nobody owns.
  • Interconnection paperwork. The Missouri Public Service Commission is the utility regulator: net metering and interconnection rules for electrical corporations, which fall on the customer and the utility. A contractor who prepares the application for a customer is still doing work the customer relies on, so check every form before it goes in and keep a copy of what you submit.

Code adoption left to counties and cities, and a state that does not inspect

Missouri has no statewide electrical code. State law leaves the adoption of electrical codes to cities and counties, and the state’s electrical contractor office says the state issues no permits and inspects no work.

Solar wiring is built to the electrical code the city or county where the job sits has adopted, which can differ between jurisdictions, and the permit and inspection come from that local building department.

Authority: RSMo 64.170; RSMo 324.925(3)

The statute on county commissions reaches wiring too. A county commission is empowered

“to adopt by order or ordinance regulations to control the construction, reconstruction, alteration or repair of any building or structure and any electrical wiring or electrical installation”

The electrical contractor law leaves the same door open to cities and counties alike. Among the things a political subdivision is not prohibited from doing is this:

“Implementing an electrical code based upon the National Electrical Code”

The Office puts the state’s own role plainly in its answers for contractors:

“The state will not be issuing permits nor will the state be inspecting the work performed.”

That is the extent of the state’s part. Adoption sits with the county or the city, and the permit and the inspection come from the local building department. The statutes allow a code based on the National Electrical Code; they do not say that every place has adopted a code, or the same edition, so what your wiring is built to is a local answer.

As advice, ask the permitting office for the code and edition it applies before the design is final, because a crew that works in different jurisdictions may meet different answers, and mark the answer on the job ticket the crew carries. A fault in finished wiring that surfaces after the inspection is a liability question, taken up on the general liability page.

Placing a Missouri crew’s comp: authorized carrier, residual market or self-insurance

Workers’ compensation is compulsory in Missouri for the employers its law covers. A covered employer insures its entire liability with an insurance carrier authorized in Missouri, or satisfies the Division of Workers’ Compensation that it can carry the liability itself, individually or as a group. Construction employers are covered at a lower employee threshold than other employers, and there is no state fund that sells coverage.

A solar contractor, as a construction employer that erects, alters or repairs improvements, is covered as soon as it has employees; it carries a workers’ compensation policy from an authorized insurer, uses the residual market if the voluntary market declines it, or qualifies with the Division to self-insure.

Authority: RSMo 287.280(1); RSMo 287.030(1)(3); RSMo 287.921

The compensation statute states the duty in a sentence that sets the pattern for everything after it:

“Every employer subject to the provisions of this chapter shall, on either an individual or group basis, insure their entire liability under the workers' compensation law”

The sentence goes on to give the employer routes. Continuing, the employer may insure

“with some insurance carrier authorized to insure such liability in this state, except that an employer or group of employers may themselves carry the whole or any part of the liability without insurance upon satisfying the division of their ability to do so”

Whether the employer is covered at all depends on the statute’s definition of an employer. For the trade this page serves, the definition reads:

“construction industry employers who erect, demolish, alter or repair improvements shall be deemed an employer for the purposes of this chapter if they have one or more employees”

The statute also provides for the contractor the voluntary market declines. The residual market plan, run through the insurers, is described this way:

“All insurers authorized to write workers' compensation and employers' liability insurance shall participate in such plan”

For a solar business that adds up to a direct path. The policy comes from an insurer authorized in Missouri, chosen in the private market; the residual market is the fallback if the voluntary market turns the business down; and the Missouri Division of Workers’ Compensation is the body that decides whether an employer, or a group, may carry the liability itself. No state fund sells a policy to the employer, so there is no public option to wait for.

How crews are classified and how subcontractors are treated at audit are policy questions rather than Missouri questions, set out on the workers’ compensation page. As advice, settle before the season who on each job is your employee, and collect a certificate from every subcontractor before its people set foot on an array.

Missouri’s Division of Workers’ Compensation and Division of Professional Registration are listed below. For fall hazards, the federal page is OSHA’s Fall Prevention Campaign.

From the registration division to the Attorney General: Missouri’s offices

The Missouri Department of Commerce and Insurance is the state’s insurance regulator; approves the residual market plan and licenses insurers. Any agency that sells you a policy, this agency among them, can be looked up on NIPR.com.

The other public bodies behind this page, each linked to its own site and followed by its role:

Absent on purpose: a statewide solar license, a statewide electrical code and a state fund that sells workers’ compensation. In an ordinary week the offices that matter are the building, permitting and licensing departments of the cities and counties where your crews work, and the carrier that holds your policy.

Metro areas drawn along Missouri’s county lines

The cards below show the largest metropolitan areas with a principal city in Missouri, as the U.S. Census Bureau delineates them, and the Missouri counties inside each.

St. Louis, MO-IL

Part of this metro lies beyond the state line; this card names its Missouri counties only: Franklin County, Jefferson County, Lincoln County, St. Charles County, St. Louis County, St. Louis city and Warren County.

Kansas City, MO-KS

Part of this metro lies beyond the state line; this card names its Missouri counties only: Bates County, Caldwell County, Cass County, Clay County, Clinton County, Jackson County, Lafayette County, Platte County and Ray County.

Springfield, MO

Made up of Christian County, Dallas County, Greene County, Polk County and Webster County.

Columbia, MO

Made up of Boone County, Cooper County and Howard County.

Joplin, MO-KS

Part of this metro lies beyond the state line; this card names its Missouri counties only: Jasper County and Newton County.

Jefferson City, MO

Made up of Callaway County, Cole County, Moniteau County and Osage County.

A county line matters here because counties hold their own power to license wiring and to adopt regulations on it. As advice, log the county and the city for every job you price, and do not assume that what satisfied the permit office in a metro’s principal city carries to its neighboring counties.

Policy pages for a state with an optional license and locally chosen codes

The policies that answer for the work are the ones a solar business carries wherever it works, and each has its own page:

  • Wiring built to a local code and damage to the roof or building under the array point to general liability.
  • Safety and performance statements in a proposal, and the designs a customer relied on, point to professional liability.
  • The compulsory comp law and the residual market point to workers’ compensation.
  • Trucks and trailers that carry modules and racking between the yard and the job point to commercial auto.
  • Your own gear and the materials staged for a job point to tools and equipment.
  • Contracts that ask for limits above the primary layer point to umbrella liability.

Which of those weigh heaviest depends on the work, and the pages on rooftop installation, panel cleaning and maintenance and ground-mount and solar farm construction take each kind of work on its own terms. When you are ready to put the pieces together for Missouri jobs, a quote request is the place to start.

Missouri: what the state sets for solar contractors, what each rule leaves open, and the coverage page that discusses it.
License to install The state offers a voluntary credential, and the local license governs
Damage to the roof, the building or a neighbor’s property from the installation work General Liability
Solar sales and installer rules The state sets its own rules for solar sellers, installers or providers
A design, sizing or output estimate the customer relied on that turns out wrong Professional Liability
Electrical code No statewide electrical code; local codes govern
A wiring or tie-in fault traced back to the work after the job is done General Liability
Workers’ compensation Required for covered employers, bought in the open market
A crew member hurt on the job Workers’ Compensation

State rules decide who may do the work and how; the policies decide who pays when something goes wrong.

  • A license, registration or certification is a requirement of the state, not insurance.

A panel for Missouri in rows. Each row sets a requirement of the state beside the exposure that requirement leaves open and the coverage line that answers it. License to install: The state offers a voluntary credential, and the local license governs. It leaves open damage to the roof, the building or a neighbor’s property from the installation work, which General Liability answers. Solar sales and installer rules: The state sets its own rules for solar sellers, installers or providers. It leaves open a design, sizing or output estimate the customer relied on that turns out wrong, which Professional Liability answers. Electrical code: No statewide electrical code; local codes govern. It leaves open a wiring or tie-in fault traced back to the work after the job is done, which General Liability answers. Workers’ compensation: Required for covered employers, bought in the open market. It leaves open a crew member hurt on the job, which Workers’ Compensation answers. Notes: A license, registration or certification is a requirement of the state, not insurance. The conclusion reads: State rules decide who may do the work and how; the policies decide who pays when something goes wrong. No figures are shown.

Missouri solar contractor insurance questions

Do we have to hold the statewide electrical contractor license to put arrays on Missouri roofs?

No. The Missouri Office of Statewide Electrical Contractors states that the statewide license is optional, not mandatory, and the statute frees a contractor from it where a city or county asks for no local license. Where a place does license electrical contractors, a local license or the state license can meet that requirement. Ask the building department of each place you bid which license it wants on file.

A county we have never worked in wants its own electrical contractor license. Does our state license settle that?

The statute lets a political subdivision set up its own electrical contractor license, but says it shall recognize a statewide license in lieu of a local license. So a contractor holding the state license can offer it in place of the local license. The permit still comes from the local building department, because the state issues no permits, so call the office and confirm its filing steps.

Is there a Missouri electrical code my designer can draw to, or does each place pick its own?

Missouri has no statewide electrical code. Counties may adopt regulations controlling electrical wiring, the electrical contractor statute leaves political subdivisions free to implement a code based on the National Electrical Code, and the Missouri Office of Statewide Electrical Contractors says the state does not inspect the work. Your designer should ask the permitting office of each job’s city or county which code it applies.

Does the net metering Act put our sales proposals under the Attorney General’s watch?

It can. The Act subjects the sale of a customer’s generation unit to the state’s merchandising practices law, and it authorizes the Missouri Attorney General to adopt rules on mandatory disclosures by sellers. Its liability clause for knowingly misrepresenting safety applies to a seller or installer. Write safety and performance statements you can support, and keep the support in the job file.

We install for a developer and never deal with the customer. Does the Act’s liability language still reach us?

The clause names the seller, installer or manufacturer of a generation unit, and it applies where the person knowingly misrepresents the unit’s safety aspects. An installer is named, whoever pays for the work. Because the clause is about knowing misrepresentation, the practical protection is accurate paperwork: what your crew installed, how it was tested and who certified the installation to the utility.

We hire a helper for rooftop jobs. Does Missouri expect us to carry workers’ compensation?

Yes, if the law covers you, and for a construction employer that erects, alters or repairs improvements the statute brings you in at a lower employee threshold than other employers face. A covered employer insures through a carrier authorized in Missouri or satisfies the Missouri Division of Workers’ Compensation that it can carry the liability itself. Place the policy before the helper climbs a ladder.

What are our choices for meeting the workers’ compensation law when no state fund exists?

Missouri has no state fund that sells coverage. A covered employer buys from an insurer authorized in the state, and if the voluntary market declines the business, the residual market plan that authorized insurers must participate in is the fallback. Or the employer, individually or in a group, satisfies the Missouri Division of Workers’ Compensation of its ability to carry the liability. Your agent can describe which route fits your payroll.

This page describes insurance for solar contractors operating in this state. It is general information, not legal advice and not a statement of coverage. Licensing, interconnection and code requirements change; verify current requirements with the agency named before relying on them.

Get a quote for your Missouri solar contracting business

Tell us which Missouri cities and counties your crews work in, whether you hold the state electrical license or local ones, and how your crew is paid, and we will build a program around those answers.