Solar Contractor Insurance by State

Arizona Solar Contractor Insurance

Arizona writes the paperwork of a solar sale into statute, licenses solar contractors statewide, leaves the electrical code to each city and county, and requires workers’ compensation of employers with a regular workforce.

Workers in hard hats and high-visibility jackets walk through tall grass beside a long row of ground-mounted solar panels.

In Arizona, the paperwork of a solar sale is written into statute: an agreement to sell or lease a distributed energy generation system must carry a list of disclosures, a savings claim must show its method, and a home system comes with a warranty statement on a form the Arizona Registrar of Contractors approves. The same Registrar licenses the contractor statewide, under a solar contractor qualification and a classification fit for the work. The electrical code is a local matter, adopted by each city and county rather than by the state, and workers’ compensation is compulsory for an employer with a regular workforce, with no state fund.

So the documents carry more of the state’s weight than the code book does. The policies themselves are explained on the solar contractor insurance page and the coverage pages it links to. What follows keeps to Arizona, for a business doing rooftop installation, running panel cleaning and maintenance routes or taking on ground-mount and solar farm construction.

How far each Arizona rule reaches, from the duties on any employer and any contracting job down to those written only for a rooftop array on a home.

A waterfall that narrows as it descends, each step reaching a smaller set of jobs than the step above it. At the top, workers’ compensation is compulsory for any employer with a regular workforce, met through an authorized carrier or self-insurance or a pool the industrial commission approves, with no state fund. Below it, every installation is built to the electrical code its city or county has adopted, because the state adopts none. Any contracting job then needs a license in good standing from the registrar of contractors, in a classification that fits the work. Narrower again, installing, altering or repairing a solar device requires the solar contractor qualification. An agreement to sell or lease an on-site distributed generation system must carry written disclosures, and any savings claim must show its method. A home or multifamily system adds a warranty statement on a form the registrar approves, a compliance certificate and the registrar’s training standards. At the bottom, a rooftop install on a home adds a roof evaluation before the work, repair of roof damage the work causes and the buyer’s signed acknowledgment about future roof repair. No figures are shown.

The agreement, the savings claim and the buyer’s signature

Arizona law sets what a sale or lease agreement for a distributed energy generation system must disclose — among them the major components or an output guarantee, the total cost, warranty periods, tax incentives and obligations, maintenance costs and the basis of any savings estimate — and requires a warranty, a registrar-approved warranty statement and a compliance certificate for residential solar energy devices.

Authority: A.R.S. 44-1763; A.R.S. 44-1762; A.R.S. 44-1761

The disclosure section is written for distributed energy generation, not for solar by name, though a solar array sold or leased for use on site is the system it describes. Its opening reaches past homeowners to any buyer, public bodies included:

“An agreement governing the sale or lease of a distributed energy generation system to any person or a political subdivision of this state must:”

What follows that opening is a list of contents: the major components or an output guarantee, the total cost, the warranty periods, tax incentives and obligations, maintenance costs and the basis for any savings estimate. A further subsection turns from the agreement to whatever the sales team says before it:

“If a document or sales presentation relating to a distributed energy generation system states or suggests that the distributed energy generation system will result in financial savings for a buyer or lessee, the document or sales presentation must substantiate the methodology”

The clause names a document or sales presentation, not only the signed agreement. As advice, read it as covering the brochure, the tablet presentation at the kitchen table and the spreadsheet sent after the visit, treat a projected bill reduction or a payback period as a savings claim, and keep a written method behind every estimate your salespeople use, date it, and store the version a customer saw with the agreement that customer signed.

For a home system, the section adds a step before signing:

“Before entering into a contract for the purchase or lease of a residential solar energy system, the licensed contractor shall obtain a written acknowledgment from the buyer or lessee”

The acknowledgment is about the roof under the array: it tells the buyer or lessee that the roofing or the structure may need repair or replacement during the agreement. A removal and reinstall for a reroof is the obvious case. As advice, say in the agreement who arranges that work and who pays for it, so the acknowledgment and the price tell the same story.

The disclosures fall on the seller, installer or contractor that writes the agreement, and a savings claim in any sales document or presentation must show its method. For a residential system the installer must also meet the Registrar of Contractors’ education, training and examination standards, evaluate the roof before a rooftop installation and repair roof damage the installation causes, and obtain the buyer’s written acknowledgment about future roof repair. Contractors that miss these standards face Registrar discipline.

A savings estimate that misses is the kind of complaint where nothing is damaged and a customer still claims a loss. How a policy treats it is set out on the professional liability page.

Home systems: a warranty statement, a roof evaluation and installer standards

A second statute in the same chapter speaks of a solar energy device and lays its duties on the contractor that installs such a device. Its definition settles where those duties stop. After listing the heating, cooling, electrical, mechanical and daylighting uses a device may serve, it says the term

“is limited to a system that is used primarily to serve on-site demand at a residential dwelling unit or multifamily structure.”

So the warranty, installer and roof rules below are written for home and multifamily systems, while the agreement disclosures above follow any on-site distributed generation sale. Commercial rooftops and utility-scale projects sit outside the device definition.

The warranty comes with a statement whose form the Registrar controls:

“The form of the statement required by this subsection is subject to approval by the registrar of contractors.”

The buyer also receives a certificate that the installation complies with the statute. The installer, in addition to holding the solar contractor qualification, must

“Meet any education and training standards that have been adopted by the registrar of contractors.”

and, on a roof, the statute adds a duty that comes before any rail is set. Before the initial installation, the licensed contractor

“shall Evaluate the roof and roofing components to determine whether the roof is capable of supporting the installation”

The record’s obligation sentence puts the rest of that duty plainly: the contractor repairs roof damage the installation causes. As advice, treat the roof evaluation as a document rather than a glance from the ladder. Note the roof covering, its age as the owner reports it, soft spots, prior repairs and the attachment plan, photograph each slope, and have the crew lead sign it. If a leak shows up later, that file is where the conversation starts.

Keep the approved warranty statement form in your contract packet, hand over the compliance certificate at closeout, and track which employees have met the Registrar’s training standards.

Damage to the roof, the house or the contents below from the installation itself is a general liability question, and that page explains how a policy reads a leak found after the job is finished.

A Registrar license, the solar qualification and the class behind the wiring

Arizona licenses solar installation statewide through the Registrar of Contractors. State law makes it unlawful for a contractor to install, alter or repair a solar device without qualifying as a solar contractor, and requires anyone installing a photovoltaic device to hold an appropriate contractor’s license.

A solar crew needs a contractor’s license in good standing from the Registrar of Contractors in the classification that fits the work, together with the solar contractor qualification, and must meet any education, training and examination standards the Registrar has adopted for the type of system installed.

Authority: A.R.S. 32-1170.01; A.R.S. 44-1762(E); A.R.S. 32-1151

The prohibition at the center of the solar contractor article reads:

“it is unlawful for a contractor to install, alter or repair a solar device without qualifying as a solar contractor pursuant to this article.”

The article’s definition of that device opens this way, then lists boilers and piping, plumbing, comfort heating and cooling, hot water and daylighting, with no mention of photovoltaic power:

“"Solar device" means a device for the use and application of solar energy incidental to:”

Photovoltaic work is reached through the solar device statute in the consumer chapter instead. It requires the installer to be a licensed solar contractor and, beyond that, to hold the license that fits the device:

“An individual who installs a solar energy device in this state, in addition to being a licensed solar contractor under title 32, chapter 10, article 4, shall:”

“Installers of a solar water heater or a photovoltaic device shall possess an appropriate contractor's license.”

Which license is appropriate for an array is a question the Registrar’s classification table answers rather than the statute. The table lists no classification for photovoltaic work by name, and the classes that carry the word solar in their titles are pool, plumbing, boiler and air conditioning classes for solar heating. What it does list are electrical classifications for residential, commercial and dual work. The residential classification is scoped this way:

“This classification allows the licensee to install and repair residential electrical systems.”

The contracting statute also draws the utility hookup into the definition of a contractor, which is the step where an array’s tie-in meets the meter:

“Connect such a structure or improvements to utility service lines and metering devices and the sewer line.”

The license, in other words, follows the work and the building. As advice:

  • Before taking on a new kind of job, a carport on a retail lot or a battery added to a home system, ask the Arizona Registrar of Contractors whether your classification reaches it, and get the answer in writing.
  • When an electrical subcontractor does the tie-in, check its license in the Registrar’s records and collect its certificate of insurance with the subcontract.

How a liability policy treats the electricians and roofers you hire, and damage your own crews cause, is set out on the general liability page.

An electrical code chosen by each city and county

Arizona has no statewide electrical code. The Legislature’s own staff describe Arizona as a home rule state where local codes are adopted and enforced locally, and state law leaves the adoption of electrical codes to cities and counties.

Solar wiring is built to the electrical code the city or county where the job sits has adopted, and state law requires a solar installation to meet the fire, safety and building codes prescribed by the local authority with jurisdiction.

Authority: A.R.S. 11-861; A.R.S. 34-461; A.R.S. 9-802; A.R.S. 44-1762(G)(1)

The plainest statement of the arrangement comes from the Senate’s own staff, writing about energy codes. It is staff analysis, not the law, but it says outright what the statutes leave implied:

“Arizona is classified as a home rule state, meaning that local codes are adopted and enforced locally.”

The statutes hand the choice to local government. A county board of supervisors may adopt

“Any building, electrical, plumbing or mechanical code that has been adopted by any national organization or association that is organized and conducted for the purpose of developing codes or that has been adopted by the largest city in that county.”

Where no local code has been adopted at all, a public building borrows the codes of a nearby city. Its design or construction follows

“the building, plumbing, electrical and mechanical codes that apply in the largest city in the county in which the building is located.”

The solar device statute points the installer the same way. Among the requirements an installation must meet are

“All fire, safety and building codes as prescribed by a local authority that has jurisdiction.”

This page quotes no state rule naming an electrical code edition, because the state adopts none. The edition and any amendments come from the city or county where the array goes up, and neighboring jurisdictions a short drive apart may differ on each. As advice:

  • Ask each permitting office which code and local amendments its inspectors apply before the design is finished, not after the plan review comes back.
  • When a job sits on unincorporated land, ask whether the county has adopted a code for that area at all, and what governs if it has not.

A wiring or tie-in fault found after the job is closed is a completed-work question, and the general liability page explains how a policy answers it.

Compulsory comp, and the subcontractor’s crew counted as yours

Workers’ compensation is compulsory in Arizona for every employer that regularly employs workers in its business. The employer insures with a carrier authorized by the Department of Insurance and Financial Institutions or proves to the Industrial Commission of Arizona that it can pay compensation directly or through an approved pool, and the law allows no other mechanism. There is no state fund.

A solar contractor with employees carries a workers’ compensation policy from an authorized carrier, or qualifies with the Industrial Commission to pay benefits itself. A general contractor that keeps supervision or control over work that is part of its business is treated as the employer of its subcontractors’ employees.

Authority: A.R.S. 23-902(A)–(B); A.R.S. 23-961(A)–(B)

The requirement reaches the employer through its workforce. The statute’s employer definition takes in

“every person who employs any workers or operatives regularly employed in the same business or establishment under contract of hire”

The duty is then stated in a short sentence, followed by the routes:

“Employers shall secure workers' compensation to their employees in one of the following ways:”

“By insuring and keeping insured the payment of such compensation with an insurance carrier authorized by the director of the department of insurance and financial institutions to write workers' compensation insurance in this state.”

Self-insurance and approved pools sit beside the carrier route, with the Industrial Commission of Arizona deciding who qualifies. The statute then closes the list:

“An employer may not secure compensation to comply with this chapter by any mechanism other than as provided in this section.”

Arizona formerly had a state fund. The article that created it was repealed, and a session law converted the fund into a mutual insurer that operates like any other licensed mutual casualty insurer. The same session law describes its standing this way:

“The successor mutual insurer corporation is not an agency of this state or a public entity of this state.”

So there is no public option to fall back on: the policy comes from an authorized carrier, unless the commission has approved the business to carry its own risk.

On a crowded job site, the clause about subcontractors deserves close attention. Where the original employer keeps supervision or control over work that is part of its business,

“then the contractors and the contractor's employees, and any subcontractor and the subcontractor's employees, are, within the meaning of this section, employees of the original employer.”

Where trenching, racking or electrical work is subcontracted, that clause can bring a subcontractor’s injured worker back to your business. As advice, collect a current certificate from every subcontractor before its crew arrives and check the dates against the job schedule. How classification, audits and crews that travel are handled is set out on the workers’ compensation page. Nothing here reaches past Arizona’s border; a job in a neighboring state is governed by that state’s law.

Among the bodies listed below is the Industrial Commission of Arizona, and the state issues a solar-specialty license. The federal side of working at height is a different page: OSHA’s Plan, Provide, Train campaign on falls, which names roof work and personal fall arrest systems.

The Registrar, the commission and the insurance department

The public bodies behind the findings above each hold a different part of a solar contractor’s obligations. Each link goes to the body’s own site, with its role as the record gives it.

The insurance department is also the regulator for the agency that places your program, this agency included, and an agency’s license can be looked up on NIPR.com. No state body on this list adopts an electrical code, since that choice belongs to cities and counties, and none of them runs a workers’ compensation fund.

Where Arizona’s larger metros sit on the county map

The cards below list the largest metropolitan areas with a principal city in Arizona, as the U.S. Census Bureau delineates them, and the Arizona counties inside each.

Phoenix-Mesa-Chandler, AZ

Made up of Maricopa County and Pinal County.

Tucson, AZ

Made up of Pima County.

Prescott Valley-Prescott, AZ

Made up of Yavapai County.

Lake Havasu City-Kingman, AZ

Made up of Mohave County.

Yuma, AZ

Made up of Yuma County.

Flagstaff, AZ

Made up of Coconino County.

In Arizona the license travels and the code does not. The Registrar’s license is good in every county on these cards, but the electrical code is whatever the city or county around the job has adopted. As advice, record the jurisdiction for every job you price, and do not assume that a metro’s suburbs inspect to the code its principal city uses.

Which policy pages pick up each Arizona duty

The statutes above set duties; the policies a solar business carries are what respond when a duty goes unmet or a job goes wrong. Each line has its own page:

  • The roof evaluation, the repair duty and finished wiring built to a local code lead to general liability, along with the subcontracted electricians and roofers on the job.
  • The savings method and the output guarantee in an agreement lead to professional liability, for estimates a customer relied on.
  • The compulsory comp law and the subcontractor clause lead to workers’ compensation, placed with an authorized carrier.
  • Crews and loaded trailers moving between jobs in different counties lead to commercial auto.
  • Modules, inverters and meters in transit or staged on site lead to tools and equipment.
  • Commercial and developer contracts that ask for limits above the primary policies lead to umbrella liability.

The weight of each line shifts with the work, and the pages on rooftop installation, panel cleaning and maintenance and ground-mount and solar farm construction take each kind on its own terms. A quote request is where an Arizona program starts.

Arizona: what the state sets for solar contractors, what each rule leaves open, and the coverage page that discusses it.
License to install A state license reaches solar installation
Damage to the roof, the building or a neighbor’s property from the installation work General Liability
Solar sales and installer rules The state sets its own rules for solar sellers, installers or providers
A design, sizing or output estimate the customer relied on that turns out wrong Professional Liability
Electrical code No statewide electrical code; local codes govern
A wiring or tie-in fault traced back to the work after the job is done General Liability
Workers’ compensation Required for covered employers, bought in the open market
A crew member hurt on the job Workers’ Compensation

State rules decide who may do the work and how; the policies decide who pays when something goes wrong.

  • A license, registration or certification is a requirement of the state, not insurance.

A panel for Arizona in rows. Each row sets a requirement of the state beside the exposure that requirement leaves open and the coverage line that answers it. License to install: A state license reaches solar installation. It leaves open damage to the roof, the building or a neighbor’s property from the installation work, which General Liability answers. Solar sales and installer rules: The state sets its own rules for solar sellers, installers or providers. It leaves open a design, sizing or output estimate the customer relied on that turns out wrong, which Professional Liability answers. Electrical code: No statewide electrical code; local codes govern. It leaves open a wiring or tie-in fault traced back to the work after the job is done, which General Liability answers. Workers’ compensation: Required for covered employers, bought in the open market. It leaves open a crew member hurt on the job, which Workers’ Compensation answers. Notes: A license, registration or certification is a requirement of the state, not insurance. The conclusion reads: State rules decide who may do the work and how; the policies decide who pays when something goes wrong. No figures are shown.

Nearby states we also write

Arizona solar contractor insurance questions

Does the Registrar print a license class written for photovoltaic work?

Not by that name. The Arizona Registrar of Contractors lists electrical classifications for residential, commercial and dual work, and the classes carrying the word solar are heating classes for pools, plumbing, boilers and air conditioning. State law still requires an installer of a photovoltaic device to hold an appropriate contractor’s license along with the solar contractor qualification. Ask the Registrar which classification fits your scope before you bid, and keep its answer on file.

Our sales deck promises customers a lower power bill. What does Arizona law ask of that slide?

If a document or sales presentation states or suggests that a distributed energy generation system will save the buyer or lessee money, it must show the method behind the savings. As advice, put the assumptions on the slide itself, keep the calculation with the signed agreement, and have the person who built the estimate check every number a salesperson quotes before it reaches a customer.

Before a rooftop install on a home, what must our crew check and what must the buyer sign?

Before the initial installation, the licensed contractor evaluates the roof and its components to decide whether the roof can carry the system, and repairs roof damage the installation causes. Before the contract is signed, the contractor obtains the buyer’s or lessee’s written acknowledgment that the roof may need repair or replacement during the agreement. Keep the evaluation, with photographs, in the job file.

A developer hired us to build a ground-mount project. Do the solar sales and warranty rules follow us there?

Read as written, they are aimed at on-site systems. The agreement disclosures reach a distributed energy generation system defined by on-site consumption, and the warranty, installer and roof rules reach a solar energy device serving a residential dwelling or multifamily structure, which leaves out utility-scale projects. A solar farm builder sits outside each, so the contract and the developer’s exhibits set the terms.

Our crews cross from city limits into unincorporated county land. Does the electrical code change at that line?

It can. Arizona has no statewide electrical code. Cities adopt codes by reference, and a county board of supervisors may adopt a building, electrical, plumbing or mechanical code for its zoned unincorporated areas, so the city and the county around it may not use the same code. Ask each permitting office which code and amendments its inspectors apply, and note the answer on the job.

Can we let a trenching subcontractor’s laborers onto our site without checking their comp?

Not safely. Where a contractor keeps supervision or control over work that is part of its business, the law treats the subcontractor and its employees as employees of the original employer. If the subcontractor carries no coverage, a claim from its laborer can land on your policy. Collect a current certificate before anyone starts work, and keep it with the subcontract.

A competitor says it still buys comp from the old state program. Is there a state fund in Arizona?

No. The article that created the former state fund was repealed, and a session law converted the fund into a mutual insurer that operates like any other licensed mutual casualty insurer and is not an agency or public entity of the state. Coverage comes from a carrier the Arizona Department of Insurance and Financial Institutions authorizes, or from self-insurance or a pool the Industrial Commission of Arizona approves.

This page describes insurance for solar contractors operating in this state. It is general information, not legal advice and not a statement of coverage. Licensing, interconnection and code requirements change; verify current requirements with the agency named before relying on them.

Get a quote for your Arizona solar contracting business

Share the license your company holds, whether your jobs go on houses, businesses or open ground, and which Arizona counties you work in, and we will shape a program around them.