Solar Contractor Insurance by State
Mississippi Solar Contractor Insurance
Mississippi licenses solar work through its State Board of Contractors, leaves electrical codes to counties and municipalities under a state directive, has not confirmed a state rulebook for solar sellers, and makes workers’ compensation compulsory for covered employers.
Mississippi licenses solar work at the state level: the Mississippi State Board of Contractors issues a residential solar license for homes and a solar and wind construction classification for commercial systems, and a crew that makes electrical or mechanical connections must hold that classification as well. Whether the state sets its own consumer rules for solar sellers and installers is not confirmed at the state level, and neither is the electrical code edition, because counties and municipalities adopt codes under a state directive that lets them opt out. Workers’ compensation is compulsory for covered employers, bought from an insurer or through the Mississippi Workers’ Compensation Commission’s approval to self-insure, with no state fund among the routes.
The points left unconfirmed matter as much as the license. A rule that has not been confirmed is not a rule that does not exist, so the sections below say what the sources support, quote them where they speak, and put the open questions to the offices that can answer them.
How the policies themselves work for a solar business anywhere is laid out on the solar contractor insurance page and the coverage pages it links to. This page keeps to what is particular to Mississippi, whether your business does rooftop installation, runs panel cleaning and maintenance routes or takes on ground-mount and solar farm construction.
A stack of layers beneath a Mississippi solar job, read from the top down. At the top is the license from the State Board of Contractors: a tested residential solar license for homes, and a solar and wind construction classification for commercial systems. Beneath it are the connections, where the board says the electrical or mechanical classification must also be held to do the wiring, grounding and piping hookups. Next is a layer marked as not confirmed at the state level: whether the state sets its own consumer rules for solar sellers and installers beyond the board license. Below that are the building and electrical codes, which counties and municipalities adopt under a state act that directs adoption and allows an opt-out by resolution, with no electrical code edition confirmed at the state level. At the bottom is workers’ compensation, compulsory for covered employers through an insurer or approved self-insurance, with no state fund and small employers left voluntary. No figures are shown.
A Board license cut to the kind of work: residential solar, or solar and wind construction
Mississippi licenses solar installation at the state level. The State Board of Contractors issues a residential solar contractor license, which the residential builders chapter requires of anyone acting as a residential solar contractor, and a stand-alone Solar and Wind Construction classification for commercial work. A crew that makes electrical or piping connections must also hold the electrical or mechanical classification.
A solar contractor holds the Board license that matches the work: the residential solar license for residential systems, and the solar and wind construction classification for commercial systems. Wiring and piping connections need the electrical or mechanical classification as well, so a firm that wires its own jobs holds that license beside its solar license.
Authority: Miss. Code Ann. § 73-59-1; § 73-59-3; § 31-3-21
The Board’s own classifications page draws the line between homes and commercial systems. For homes it says:
“A residential license classification that involves installation, maintenance, and repair of residential solar and photovoltaic systems. Contractors must also hold the required classification to make electrical or mechanical connections. The holder of this classification is limited to residential solar work only.”
For commercial work the Board keeps a separate classification, described this way:
“A specialty classification that involves construction, installation, alteration, repair and maintenance of alternative energy structures and equipment including solar panels and photovoltaic systems and appurtenances, apparatus, or equipment used in connection therewith.”
Read the limit in the residential description: the holder is confined to residential solar work. A firm that takes a commercial array on a residential license is working outside the classification the Board describes. As advice, sort every job at intake by the kind of building under the array, and write the license that covers the job into the proposal file before the price goes out.
The Mississippi State Board of Contractors site is where a business confirms how its classification is described.
Connections that call for the electrical or mechanical classification
A solar license does not stand alone on a job with wiring. Under its description of the commercial classification, the Board adds a sentence about the work that sits next to the panels:
“If any piping or electrical connections are necessary, the appropriate electrical or mechanical classification would be required to perform piping work, hookups, grounding, or wiring.”
The electrical side has a classification of its own, which the Board describes as a major classification:
“A major classification that involves installation, repair, alteration, addition to or design of electrical wiring, fixtures, appliances, apparatus, raceways, conduit, or any part thereof, which generates, transmits, transforms, or utilizes electrical energy in any form”
Put those together and the division of labor on a roof is plain. The solar license covers the solar work the Board describes; the wiring, grounding and piping hookups belong to whoever holds the electrical or mechanical classification. As advice, decide before the bid which of those licenses your own firm holds, and which comes from a subcontractor.
- If your crew wires its own jobs, tell your agent which classification backs that work, so the program is built on accurate facts.
- If an electrician lands the conductors, collect that electrician’s license with its certificate of insurance and file them together.
- If a mechanical contractor handles piping on a thermal system, treat it the same way.
How a liability policy treats the electricians you bring in, and a fault in finished wiring that comes to light after the job is done, is set out on the general liability page.
The statutes behind the license: a residential chapter and a certificate of responsibility
The Board also reprints the statutes it administers. The residential builders chapter lists, among the persons it reaches, these:
“Persons or entities acting in the capacity as a residential solar contractor.”
The same chapter defines the term, in a definition that reaches thermal systems as well as photovoltaic ones:
“means any person or entity that installs, modifies, maintains, and repairs thermal and photovoltaic solar energy systems.”
The contractors chapter works through a different instrument, a certificate of responsibility:
“It shall be unlawful for any person who does not hold a certificate of responsibility issued under this chapter to submit a bid, enter into a contract”
The quote is the opening of a sentence, and the chapter carries limits on which contracts it reaches that this page does not restate. As advice, do not read the line as a ruling on your own contract. Ask the Board how the chapter applies to the size and type of job you are bidding, and keep its answer, dated, with the proposal.
Seller and installer rules for solar: not confirmed at the state level, with the utility rules beside them
Whether Mississippi sets its own consumer rules for solar sellers, installers or providers beyond the Board of Contractors license is not confirmed at the state level.
The Public Service Commission’s distributed generation and net metering rules run between the customer and the electric utility, and the interconnection application asks for the equipment contractor and, where different, the electrical contractor and its license standing. The state’s consumer guidance sends buyers to the Board of Contractors and the Attorney General to check a firm’s license.
The finding is narrow, and the wording matters. It does not say that a rulebook for solar sellers exists, and it does not say that none does. It says that such a rule is not confirmed at the state level. The nearest rules on this page are those of the Mississippi Public Service Commission, whose role is utility regulator: distributed generation interconnection and net metering rules, which fall on the customer and the utility.
A business that sells or installs systems should hold the distinction firmly. Rules about connecting a system to the grid are not a checklist for a proposal, which is what a solar disclosure law would be. They bind the utility and the customer who owns or leases the facility. Treat the proposal as the place where any consumer question will be tested, and write it for a reader who is looking for what you promised.
As advice, build each proposal on some habits:
- State how the output estimate was produced and what it assumes about shading, orientation and equipment, so a shortfall traces to a stated assumption rather than to a vague promise.
- List every cost the customer will bear, and describe in plain words what your business does and what the customer or the utility does.
- Keep a signed copy of whatever the customer received, and a dated note of any claim a salesperson made at the door or on the phone.
- When your firm prepares the interconnection application for a customer, check every form before it goes in, since the application asks for the equipment contractor and the electrical contractor and its license standing.
If a customer relies on an estimate that turns out wrong and nothing is damaged, the claim that follows is a professional liability question rather than a general liability claim, and that page sets out how such a policy responds.
A directive to adopt local codes, an opt-out by resolution and no edition named at the state level
Mississippi leaves electrical code adoption largely to its counties and cities. State law lets a county adopt electrical codes for its unincorporated areas and directs counties and municipalities to adopt the State Uniform Construction Code unless they opt out, but no state source read names the electrical code edition that applies to a solar installation.
Solar wiring is built to the electrical code that the county or city where the job sits has adopted, and the permit and inspection come from that local building department. A contractor confirms the adopted edition with the local office before designing the system.
Authority: Miss. Code Ann. § 19-5-9; 2014 Miss. Laws, Senate Bill 2378
The state act sits at the center of that finding. In its own words, the codes a county board or municipal governing authority is directed to adopt include these:
“Other codes addressing matters such as electrical, plumbing, mechanical, fire and fuel gas, and any specific appendix or appendices as adopted and amended by the Mississippi Building Codes Council.”
The directive is not absolute. The act lets a county or municipality step out of it by resolution:
“may choose not to be subject to the code requirements imposed under this section.”
The Mississippi Building Codes Council named in the act is the body whose adopted and amended codes the counties and municipalities take up. The finding stops there, and so does this page: the Council’s adopted electrical code and its edition are not confirmed at the state level, and nothing here names an edition.
A county has a power of its own as well. The county-codes statute, as an act amending it reprints it, opens this way:
“Any county within the State of Mississippi, in the discretion of the board of supervisors, may adopt building codes, plumbing codes, electrical codes, sanitary codes, or other related codes”
And it limits the reach of what a county adopts:
“but those codes so adopted shall apply only to the unincorporated areas of the county.”
Together the quotes explain a split a contractor feels in the field. A crew that works a string of towns in a week may meet different inspectors reading from different books.
- Before the drawings are final, ask the local building department which electrical code it has adopted and whether it has opted out of the state directive, and keep the answer in the job file.
- Tell every crew lead which edition the inspector is reading from, because a design that leans on a provision the inspector’s edition does not carry can fail inspection.
A fault in wiring that comes to light after the job is finished is a general liability matter, and a clear record of the code you built to helps whoever has to answer it.
Comp that is compulsory for covered employers, with small payrolls left voluntary
Workers’ compensation is compulsory in Mississippi for employers the law covers, and the Workers’ Compensation Commission’s facts document puts coverage as voluntary for employers below a small number of regularly employed workers. A covered employer buys a policy from an insurance company or obtains the Commission’s approval to self-insure, alone or in a group.
A solar contractor with covered employees carries a workers’ compensation policy from an insurer, or qualifies with the Commission to self-insure, and proof of that coverage is filed with the Commission.
Authority: Miss. Code Ann. § 71-3-75; Mississippi Workers’ Compensation Commission Rules, Title 20, Part 1, Rules 1.3 and 1.7
The Commission’s facts document states the duty and its routes:
“An employer covered by the Law is required to secure the payment of workers' compensation benefits to its employees by purchasing workers' compensation insurance from an insurance company or by obtaining approval from the Commission to self-insure.”
The same document draws the line for small employers:
“If the employer has less than five (5) employees, workers' compensation coverage is not mandatory but may be provided voluntarily by the employer.”
The line speaks of employees, and who counts as an employee is a question for the owner and the agent, not for a quotation. A crew that grows by the season, or a helper paid by the job, can move a business across the line. As advice, settle on paper who is on the payroll before the season starts.
The Commission’s rules add the paperwork. Proof of coverage is filed with the Commission:
“Every employer within the scope of the Mississippi Workers' Compensation Law shall file proof of compliance with the insurance provisions of the Law in the manner directed by the Commission.”
And the rule on self-insurers sets the way into that route:
“and carry its own risk under the provisions of Miss. Code Ann. Section 71-3-75 shall make application on a form provided by the Commission”
For a solar business, that leaves a direct path. The policy comes from an insurer chosen in the market, unless the Mississippi Workers’ Compensation Commission has approved the business to carry its own risk. The Mississippi Insurance Department lists the residual market plans, and as advice, ask your agent what applies if insurers decline a crew, before that happens.
How roof crews, ground crews and service technicians are classified, how subcontractors are treated at audit and how a policy follows a crew that travels are policy questions rather than Mississippi questions, set out on the workers’ compensation page. Nothing on this page reaches past Mississippi’s border; for a job in a neighboring state, check that state’s rules.
In Mississippi a solar-specialty license sits beside compulsory comp, and the Mississippi Workers’ Compensation Commission is listed below. The crew’s ladders and roofs are the subject of OSHA’s Fall Prevention Campaign.
The board, the commission, the department and the council: who holds which file
The public bodies behind this page are listed here. Each link goes to the body’s own page, and each role is given as the source states it:
- Mississippi State Board of Contractors: statewide contractor licensing, including the residential solar contractor license and the solar and wind construction classification, and the electrical and mechanical classifications that cover the connections
- Mississippi Workers’ Compensation Commission: workers’ compensation administration; receives proof of coverage and approves self-insurance
- Mississippi Insurance Department: insurance regulator; lists the residual market plans, and houses the State Fire Marshal
- Office of the State Fire Marshal: promulgates and enforces the Mississippi Fire Prevention Code for state buildings, public assembly buildings and tall buildings
- Mississippi Public Service Commission: utility regulator: distributed generation interconnection and net metering rules, which fall on the customer and the utility
- Mississippi Building Codes Council: adopts and amends the codes, appendices and electrical, plumbing and mechanical codes that counties and municipalities adopt under the State Uniform Construction Code
Any agency that sells you a policy, ours among them, can be looked up on NIPR.com. Ask any agency quoting your program for its license details and check them there before you sign.
The license question goes to the Board, the coverage file to the Commission, the code question to the local building department, and the grid connection to the utility regulator.
Metro cards, including a cross-border metro whose principal city is outside the state
The cards below show the metropolitan areas with Mississippi counties, those with a principal city in Mississippi ahead of the rest, as the U.S. Census Bureau delineates them, and the Mississippi counties inside each.
Jackson, MS
Made up of Copiah County, Hinds County, Holmes County, Madison County, Rankin County, Scott County, Simpson County and Yazoo County.
Gulfport-Biloxi, MS
Made up of Hancock County, Harrison County, Jackson County and Stone County.
Hattiesburg, MS
Made up of Forrest County, Lamar County and Perry County.
Memphis, TN-MS-AR
Part of this metro lies outside Mississippi; this card lists its Mississippi counties only: Benton County, DeSoto County, Marshall County, Tate County and Tunica County.
The Board license is statewide, and so is the comp duty, so a metro line here adds only its counties. What varies from place to place is the electrical code, which the local government that has adopted it decides. As advice, log the county and the city for every job you price, and check the local building department before the proposal leaves your hands, since a metro that spans many counties is a set of separate adoptions.
Coverage lines that answer for Board-licensed work and a covered payroll
The findings above say where Mississippi’s rules sit. The policies that answer for the work are the ones a solar business carries wherever it works, and each has its own page:
- The Board license, the connections and the electricians you bring in point to general liability, which also takes up finished wiring and damage to the roof or building under the array.
- Estimates and designs a customer relied on, where a solar sales rule is not confirmed at the state level, point to professional liability.
- The compulsory comp duty and the self-insuring route point to workers’ compensation.
- Trucks and trailers that carry modules and racking between the yard and the job point to commercial auto.
- Meters, lifts and stock on the way to a job point to tools and equipment.
- Contracts that ask for limits above the primary layer point to umbrella liability.
Which of those weigh heaviest depends on the work, and the pages on rooftop installation, panel cleaning and maintenance and ground-mount and solar farm construction take each kind of work on its own terms. When you are ready to put the pieces together for Mississippi jobs, a quote request is the place to start.
State rules decide who may do the work and how; the policies decide who pays when something goes wrong.
- A license, registration or certification is a requirement of the state, not insurance.
- Solar sales and installer rules is not confirmed at the state level on this page.
- Electrical code is not confirmed at the state level on this page.
A panel for Mississippi in rows. Each row sets a requirement of the state beside the exposure that requirement leaves open and the coverage line that answers it. License to install: A state license reaches solar installation. It leaves open damage to the roof, the building or a neighbor’s property from the installation work, which General Liability answers. Solar sales and installer rules: Not confirmed at the state level. No connector is drawn for this row. Electrical code: Not confirmed at the state level. No connector is drawn for this row. Workers’ compensation: Required for covered employers, bought in the open market. It leaves open a crew member hurt on the job, which Workers’ Compensation answers. Notes: A license, registration or certification is a requirement of the state, not insurance. Solar sales and installer rules is not confirmed at the state level on this page. Electrical code is not confirmed at the state level on this page. The conclusion reads: State rules decide who may do the work and how; the policies decide who pays when something goes wrong. No figures are shown.
Mississippi coverage, services and state offices
What we insure
Coverage lines
Mississippi solar contractor insurance questions
Which Board license does our crew need for panels on a house, and which for a warehouse roof?
The Mississippi State Board of Contractors lists a tested residential solar license limited to residential solar work, and a stand-alone solar and wind construction classification for commercial systems. A firm that sets arrays on homes and on commercial buildings should ask the Board how its classifications line up with the jobs on its bid list before it prices a commercial array.
Our crew lands the conductors on its own jobs. Is the solar license enough?
The Board says a contractor must also hold the required classification to make electrical or mechanical connections, so a firm that wires its own jobs holds that classification beside its solar license. When an electrician lands the conductors, collect that electrician’s license and certificate of insurance and file them with the job.
Does Mississippi have a consumer law for solar sales that our reps must follow?
That is not confirmed at the state level. The Mississippi Public Service Commission writes distributed generation and net metering rules that run between the customer and the utility, and the state’s consumer guidance sends buyers to the Mississippi State Board of Contractors and the Attorney General to check a firm’s license. Write each proposal for a skeptical reader: say how the estimate was produced and list every cost.
Which electrical code will the inspector in a city or county we have never worked in apply?
The code that county or municipality has adopted. State law directs counties and municipalities to adopt codes unless they opt out by resolution, and a county may adopt electrical codes for its unincorporated areas only. No electrical code edition is confirmed at the state level, so call the local building department before the drawings are final and keep the answer in the job file.
Does a small payroll excuse our solar company from workers’ compensation?
The Mississippi Workers’ Compensation Commission’s facts document makes coverage compulsory for a covered employer and voluntary for an employer below a small number of regularly employed workers. Whether your crew counts turns on who is an employee. Ask your agent and the Commission before the payroll grows, and collect a certificate of coverage from every subcontractor.
Can we get workers’ compensation from a state fund, or do we self-insure?
The routes the Commission describes are a policy bought from an insurance company or the Commission’s approval to self-insure, alone or in a group. Mississippi has no state fund among them. Self-insuring starts with an application on a form the Commission provides, so treat it as a financial decision to settle with the Commission before anyone climbs a ladder.
A subcontractor holds a Board license but no comp coverage. Does the license close that gap?
No. The license says who may do the work; proof of workers’ compensation coverage is filed with the Mississippi Workers’ Compensation Commission, under its rule on proof of coverage. Ask each subcontractor for a certificate of coverage along with its license, and ask your agent how your own policy treats an uninsured subcontractor’s crew at audit.
This page describes insurance for solar contractors operating in this state. It is general information, not legal advice and not a statement of coverage. Licensing, interconnection and code requirements change; verify current requirements with the agency named before relying on them.
Get a quote for your Mississippi solar contracting business
Tell us whether your Mississippi jobs are homes or commercial systems, who holds the electrical or mechanical license on each crew and how the payroll is built, and we will shape the program around those answers.