Solar Contractor Insurance by State
Connecticut Solar Contractor Insurance
Connecticut licenses solar electricity work as its own trade, reserves the connection to a building’s wiring for unlimited electrical licensees, brings home solar sellers under its solicitation sales law, applies the electrical code through its building code and requires workers’ compensation with no state fund.
Connecticut writes a license for solar electricity work into its statutes. The Connecticut Department of Consumer Protection issues limited solar electric licenses for the array and its wiring, and leaves the connection to a building’s existing electrical system or meter to holders of its unlimited electrical licenses. Residential solar sellers now come under the state’s home solicitation sales law, the wiring is built to the electrical code the state building code adopts, and workers’ compensation is compulsory for covered employers, with no state fund.
The hard questions sit at the edges of that scheme: where the limited license stops inside the building, who on the roof needs no license, and which sales the new law reaches. Advice below is marked as advice.
What each policy does for a solar firm is set out on the solar contractor insurance page and the coverage pages behind it. Connecticut’s rules bear on a firm whatever its work, be it rooftop installation, panel cleaning and maintenance contracts or ground-mount and solar farm construction.
A top-to-bottom flow that follows the work on a Connecticut solar array and names who the state allows to do each stage. It begins on the roof, where crews hoisting, placing and anchoring panels under the direction of a licensed solar contractor are exempt from licensing for that work. The array’s wiring comes next, and it falls within the limited solar electric license, which reaches photovoltaic equipment up to a point just inside the structure; the journeyperson license under it is for work done for a licensed contractor. The connection to the building’s existing panel, wiring or utility meter follows, and the Electrical Work Examining Board reserves it to unlimited electrical licensees; a limited solar electric licensee may not make it. Last comes the permit inspection, where the local building official holds the work to the electrical code the State Building Code adopts, with the solar article as the adopted edition prints it. No figures are shown.
A trade license written for solar electricity work
Connecticut licenses solar electric work statewide. The Department of Consumer Protection issues limited solar electric contractor and journeyperson licenses for installing, repairing and maintaining photovoltaic systems, and its unlimited electrical licenses cover all electrical work, including the final connection of a solar array to a building’s wiring or utility meter.
A solar installer in Connecticut works under a state license that covers the job: a limited solar electric license reaches the array and its wiring up to a point just inside the structure, while tying into a building’s existing electrical system or meter takes an unlimited electrical license. Crews hoisting, placing and anchoring panels under a licensed solar contractor are exempt from licensing for that work, and a firm selling or contracting for work on a home also registers as a home improvement contractor.
Authority: C.G.S. §§ 20-330, 20-334, 20-340c, 20-340; C.G.S. §§ 20-419, 20-420
The licensing chapter starts from a definition. Solar electricity work, in the statute’s words,
“means the installation, erection, repair, replacement, alteration, maintenance, inspection and testing of photovoltaic or wind generation equipment used to distribute or store ambient energy for heat, light, power or other purposes to a point immediately inside any structure or adjacent to an end use”
The chapter then orders licenses built around that definition, directing the regulations that are
“to establish solar electric contractor and journeyman licenses, for solar electricity work”
and it makes a license the condition of doing the work at all:
“No person shall engage in, practice or offer to perform the work of any occupation subject to this chapter in this state”
The Connecticut Department of Consumer Protection prints the reach of the limited solar electric contractor license on its solar trades page:
“The holder of this license may perform only work limited to Solar Electric systems; which means the installation, erection, repair, replacement, alteration or maintenance of photovoltaic or wind generation systems”
The journeyperson license under it is for work done for a licensed contractor. As advice, keep a copy of each license your people hold in the permit packet, and make sure the license holder named on a permit is someone who will be on that job.
The meter and the existing panel: work for an unlimited license holder
The limited license stops short of the building’s own electrical system. The Electrical Work Examining Board, the examining board for electrical and solar electric work; clarified the limit on solar electric licensees’ connections, drew that line, and the department prints the board’s clarification beside the solar licenses:
“Connection to the buildings existing electrical system or utility meter can only be performed by a licensed E-1 or E-2 license holder.”
Those are the department’s unlimited electrical licenses. The contractor version reaches every kind of electrical work the statute defines:
“The holder of this license shall be permitted to do all electrical work as defined in section 20-330 of the general statutes.”
That turns the tie-in into a staffing question. A firm holding only limited solar electric licenses needs an unlimited licensee for the connection, on the payroll or under subcontract. As advice:
- Say in each proposal who will make the connection to the existing panel or meter, and under whose license.
- When the connection is subcontracted, collect the electrician’s license with a certificate of insurance, and brief crew leads so that nobody holding only a limited license opens the main panel to finish on schedule.
How a liability policy answers when a fire or a fault is traced to finished wiring, yours or a subcontracted electrician’s, is explained on the general liability page.
Panel crews without a license, and a registration for house jobs
Not everyone working on a Connecticut roof needs a license. The licensing chapter’s list of exemptions, as the latest supplement prints it, takes in
“employees of or any contractor employed by and under the direction of a properly licensed solar contractor, performing work limited to the hoisting, placement and anchoring of solar collectors, photovoltaic panels, towers or turbines”
The exemption is narrow: lifting, placing and anchoring, done while a properly licensed solar contractor directs the work. As advice, keep that direction visible, with a written scope for each subcontracted crew and no conductor work by anyone relying on the exemption.
Work on a home brings a separate credential. The Home Improvement Act puts it this way:
“No person shall hold such person out to be a contractor or salesperson without first obtaining a certificate of registration from the commissioner as provided in this chapter”
That registration is general rather than solar and licenses no electrical work, so it sits beside the trade license instead of standing in for it. As advice, if a sales company signs your residential contracts and your firm installs, settle in writing which entity holds the registration.
Residential solar sellers under the home solicitation sales law
Connecticut’s Public Act 26-16, now in effect, brings residential solar and energy storage sellers under the state’s Home Solicitation Sales Act. A seller of a residential rooftop solar system sold away from its place of business must give the consumer the Act’s written notice of the right to cancel, and the Act adds solar-specific duties: an identification card for door-to-door sales, a consumer handbook from the Department of Consumer Protection, and a yearly report to the Department naming the firms it partners with for financing or installation.
Authority: Public Act 26-16, §§ 1–3 (amending C.G.S. §§ 42-134a and 42-135a and adding a new section to the Home Solicitation Sales Act)
The Act names its subject in its title:
“AN ACT CONCERNING CONSUMER PROTECTIONS REGARDING RESIDENTIAL SOLAR AND ENERGY STORAGE SYSTEMS.”
Its reach turns on defined terms. A residential solar or energy storage seller
“means any person engaged in home solicitation sales of residential solar photovoltaic systems or residential energy storage systems”
and the residential systems it speaks of are those that
“are installed on the roof of a single-family dwelling or multifamily dwelling”
The duties fall on the seller and its sales representatives, and the yearly report reaches the installers a seller works with by naming them to the Department. The handbook, identification, hours and reporting duties begin on later dates the Act sets; the cancellation rights apply now. The Act reaches only residential systems on one-family homes and small multifamily buildings, not commercial or utility-scale work.
Among the duties the Act adds, a seller and its authorized sales representatives must
“Carry a current and valid identification card at all times while such residential solar or energy storage seller or authorized sales representative is engaged in any in-person solicitation at a consumer's residence”
and must
“Provide a copy of the handbook developed pursuant to subsection (a) of this section to the consumer”
The yearly report to the department is where an installer appears, even an installer that never knocks on a door. The seller files it
“disclosing the identity of each person with whom such residential solar or energy storage seller maintains a business relationship and provides any financing, installation services or any other related consumer services”
An installer working behind a sales company’s brand can expect its name in that filing. As advice, know how each sales partner describes your role to the customer.
The cancellation right is the part in force now. The Act rewrites the notice a contract must carry, in capitals as the statute prints it:
“YOU, THE [BUYER] CONSUMER, MAY CANCEL THIS TRANSACTION AT ANY TIME PRIOR TO MIDNIGHT OF THE THIRD BUSINESS DAY AFTER THE DATE OF THIS TRANSACTION.”
As advice, do not put rails on a roof while a sale can still be canceled, and check the Act’s timetable for the later duties before each sales season. Savings and output promises a customer relied on are taken up on the professional liability page.
The building code’s electrical portion, and a successor not yet in force
Connecticut adopts the National Electrical Code statewide through the Connecticut State Building Code, which applies the code to the installation of electrical systems in its commercial and residential portions alike. The state’s amendments to the electrical code change no part of its solar photovoltaic article. A newer state code is drafted and not yet in effect.
Solar wiring on a Connecticut building is built to the electrical code the State Building Code adopts, enforced by the local building official through the permit, and the solar article applies as the adopted edition prints it. Rooftop arrays on homes also meet the residential portion’s rooftop rules for roof loads, fire access pathways and signage. The replacement code still awaits approval by the legislature’s regulation review committee.
Authority: C.G.S. § 29-252; 2022 Connecticut State Building Code §§ 101.4.8, R101.4.5
The statute behind the code tells the state’s code officials to
“adopt and administer a State Building Code based on a nationally recognized model building code”
The building portion of that code then takes in the national electrical code:
“(Add) 101.4.8 Electrical. The provisions of the 2020 NFPA 70, National Electrical Code, shall apply to the installation of electrical systems, including alterations, repairs, replacement, equipment, appliances, fixtures, fittings and appurtenances thereto.”
and the residential portion names the same code for houses built under it:
“(Add) R101.4.5 Applicable electrical code. The applicable electrical code for buildings constructed under this code is the 2020 NFPA 70 National Electrical Code portion of the 2022 Connecticut State Building Code.”
Which code applies is a matter of the permit, and the Office of the State Building Inspector, Connecticut Department of Administrative Services gives the starting point:
“It applies to projects with permit applications filed from October 1, 2022.”
A successor code has been drafted, and it has not taken effect. The department’s page on code adoption explains the hold:
“at this time, we await approval of the next codes by the Legislative Regulation Review Committee of the Connecticut General Assembly, and therefore the effective date has been delayed.”
The approval it waits on belongs to the Legislative Regulation Review Committee, the legislative committee whose approval the next State Building Code awaits. Until that approval comes and a new date is set, the code quoted above governs a job permitted today. As advice, do not lean on a provision found only in the draft, and remember that roof loads, pathways and signage on houses come from the residential portion, not the electrical code. How a policy treats a wiring fault found after sign-off is explained on the general liability page.
Workers’ comp with no state fund behind it
Workers’ compensation is compulsory in Connecticut for the employers its Act covers. An employer either proves to the chairperson of the Workers’ Compensation Commission that it can pay benefits directly, or insures its full liability with stock or mutual companies authorized to take the risk in Connecticut, or files security with the Insurance Commissioner. There is no state fund; coverage comes from the private market or approved self-insurance.
A solar contractor with employees carries a workers’ compensation policy from an authorized insurer, or qualifies with the Commission to pay benefits itself.
Authority: C.G.S. § 31-284(a), (b); C.G.S. § 31-275(10)
The Act states the duty without hedging:
“an employer shall secure compensation for his employees as provided under this chapter”
The routes follow. An employer may insure its liability
“in any stock or mutual companies or associations that are or may be authorized to take such risks in this state”
or it may proceed
“By filing with the Insurance Commissioner in form acceptable to him security guaranteeing the performance of the obligations of this chapter by the employer”
The Connecticut Workers’ Compensation Commission, which handles workers’ compensation administration, dispute resolution and self-insurance approval, describes how far the requirement reaches:
“With few exceptions, all employers in the State of Connecticut are required to have workers' compensation insurance for their employees, as defined under the Workers’ Compensation Act.”
and is direct about its own part:
“WCC does not provide insurance.”
For a solar firm with a crew, that means a policy placed in the private market with an insurer authorized to take the risk in Connecticut, unless the firm qualifies to pay benefits itself or files security instead.
As advice, hold a current certificate for each subcontracted crew; the licensing exemption for hoisting crews says nothing about who answers for their injuries. Classification, audits and crews that travel are taken up on the workers’ compensation page; nothing here reaches past Connecticut’s border.
In Connecticut the Workers’ Compensation Commission and the Insurance Department are both listed below, and the solar-specialty license is a third file. A fourth, federal one is OSHA’s campaign on preventing falls, which asks employers to plan the work, provide fall protection and train the crew.
The departments and boards a Connecticut solar firm deals with
The Connecticut Insurance Department is the state’s insurance regulator; receives security filed by employers under the workers’ compensation Act. The license of any agency that sells you a policy, ours included, can be checked on NIPR.com.
The other public bodies named on this page each hold their own part of a solar firm’s obligations. Each link goes to the body’s own site:
- Connecticut Department of Consumer Protection: issues the solar electric, electrical and solar thermal trade licenses and home improvement contractor registrations; administers the residential solar seller duties of the Home Solicitation Sales Act
- Electrical Work Examining Board: examining board for electrical and solar electric work; clarified the limit on solar electric licensees’ connections
- Office of the State Building Inspector, Connecticut Department of Administrative Services: adopts the Connecticut State Building Code, including its electrical portion, with the Codes and Standards Committee, and issues code interpretations
- Legislative Regulation Review Committee: legislative committee whose approval the next State Building Code awaits
- Connecticut Workers’ Compensation Commission: workers’ compensation administration, dispute resolution and self-insurance approval
Missing from the list by design is a state workers’ compensation fund. Day to day, the offices a crew meets are the local building officials who issue permits and inspect the work under the state code.
Planning regions inside Connecticut’s metropolitan areas
The cards show the metropolitan areas with a principal city in Connecticut, as the U.S. Census Bureau delineates them, with the planning regions the Bureau lists inside each.
Hartford-West Hartford-East Hartford, CT
Made up of Capitol Planning Region and Lower Connecticut River Valley Planning Region.
Bridgeport-Stamford-Danbury, CT
Made up of Greater Bridgeport Planning Region and Western Connecticut Planning Region.
New Haven, CT
Made up of South Central Connecticut Planning Region.
Waterbury-Shelton, CT
Made up of Naugatuck Valley Planning Region.
Norwich-New London-Willimantic, CT
Made up of Southeastern Connecticut Planning Region.
The state license travels across these regions; the permit desk changes with each town. As advice, note how each building department wants a solar permit packet assembled, and price inspection time into every bid.
What each Connecticut rule asks of an insurance program
The rules above stay put; the policies that respond to a loss on a Connecticut job are the same lines a solar business carries anywhere, each with its own page:
- The limited license’s boundary at the existing panel, and the electricians who cross it for you, lead to general liability, which also takes up damage to the roof and the building.
- Hoisting crews, laborers and subcontracted installers lead to workers’ compensation, placed with an authorized insurer.
- Residential sales, the seller’s paperwork and the promises a proposal makes lead to professional liability.
- Trucks and trailers hauling modules, racking and crews from region to region lead to commercial auto.
- Meters, lifts and staged equipment between the shop and the roof lead to tools and equipment.
- Developer and commercial contracts that ask for higher limits lead to umbrella liability.
How those lines weigh against each other turns on the kind of work, and the pages on rooftop installation, panel cleaning and maintenance and ground-mount and solar farm construction take each in turn. When your Connecticut licenses, sales model and payroll are in hand, a quote request is where the program starts.
State rules decide who may do the work and how; the policies decide who pays when something goes wrong.
- A license, registration or certification is a requirement of the state, not insurance.
A panel for Connecticut in rows. Each row sets a requirement of the state beside the exposure that requirement leaves open and the coverage line that answers it. License to install: A state license reaches solar installation. It leaves open damage to the roof, the building or a neighbor’s property from the installation work, which General Liability answers. Solar sales and installer rules: The state sets its own rules for solar sellers, installers or providers. It leaves open a design, sizing or output estimate the customer relied on that turns out wrong, which Professional Liability answers. Electrical code: The state adopts the National Electrical Code statewide. It leaves open a wiring or tie-in fault traced back to the work after the job is done, which General Liability answers. Workers’ compensation: Required for covered employers, bought in the open market. It leaves open a crew member hurt on the job, which Workers’ Compensation answers. Notes: A license, registration or certification is a requirement of the state, not insurance. The conclusion reads: State rules decide who may do the work and how; the policies decide who pays when something goes wrong. No figures are shown.
Nearby states we also write
Connecticut coverage, services and state offices
What we insure
Coverage lines
Outside authorities
Connecticut solar contractor insurance questions
Our installers carry limited solar electric licenses. May they make the connection at the customer’s main panel?
No. The Electrical Work Examining Board has clarified that a limited solar electric licensee may not connect to any existing panel, wiring or circuit on the premises, and that the connection to the building’s existing system or utility meter belongs to an unlimited electrical licensee. Plan the tie-in around that person, on your payroll or under subcontract, and name them in the proposal before the job is scheduled.
We hire laborers to carry modules up and bolt them to the rails. Does each of them need a license?
Not for that work. The licensing chapter exempts employees and subcontractors of a properly licensed solar contractor who work under its direction on hoisting, placing and anchoring panels. The exemption ends where conductors begin, so keep a licensed person directing the job, write each laborer’s scope down, and keep unlicensed hands off the wiring however close the deadline.
We sell and install arrays on houses. Is the solar license enough, or do we register with the state as well?
The trade license covers the work, and a firm that sells or contracts for work on a home also registers as a home improvement contractor with the Connecticut Department of Consumer Protection. The registration is general, not solar, and licenses no electrical work, so it sits beside the solar license rather than replacing it. Check which of your entities signs residential contracts, and make sure that entity holds the registration.
Our reps knock on doors to sell rooftop systems. What does the new residential solar law ask of them?
It treats the seller as a seller under the state’s home solicitation sales law, so each contract carries the written notice of the customer’s right to cancel, and that right applies now. Identification cards, the department’s handbook, solicitation hours and a yearly report naming partner firms start on later dates the Act sets. Train reps on the cancellation notice today and calendar the later duties.
We build on warehouses and open ground and never sell to households. Does the new seller law touch our contracts?
Its reach is residential. The Act covers rooftop systems on homes and small multifamily buildings, not commercial or utility-scale work, so a warehouse roof or a ground-mount field sits outside it. Your licensing duties and workers’ compensation still apply on those jobs, and a developer’s contract will set its own terms, so read the insurance exhibit before you sign it.
We heard a newer building code was on the way. Do our permits fall under it yet?
Not yet. The Office of the State Building Inspector, Connecticut Department of Administrative Services says the effective date of the next codes has been delayed while they await approval by the Legislative Regulation Review Committee, so the code in force is the code adopted with the current State Building Code. Confirm with each building official which code a permit was filed under, and keep designs to the adopted code until a new date is set.
Our crew is small and we have never bought workers’ compensation. Does Connecticut expect us to?
If you have employees, plan on it. The Act requires covered employers to secure compensation, and the Connecticut Workers’ Compensation Commission says it does not provide insurance itself. There is no state fund, so the routes are a policy from an insurer authorized in Connecticut, security filed with the Insurance Commissioner, or approval to pay benefits directly. Arrange it before anyone on the payroll climbs a ladder.
This page describes insurance for solar contractors operating in this state. It is general information, not legal advice and not a statement of coverage. Licensing, interconnection and code requirements change; verify current requirements with the agency named before relying on them.
Get a quote for your Connecticut solar contracting business
Send us the license each of your people holds, how your residential sales are made and where in Connecticut you build, and a licensed agent will shape the coverage to fit.