Solar Contractor Insurance by State
New York Solar Contractor Insurance
New York writes solar into its home improvement contract law, registers providers that sell on-site solar on their own behalf, leaves electrician licensing to its cities and counties, wires to its Uniform Code and makes workers’ compensation compulsory.
New York writes solar into its home improvement contract law: an array on a house is a home improvement, so the contract for it must be written and signed, and before work starts it must tell the homeowner about the contractor’s property or casualty insurance. A business that sells on-site solar to residential or small commercial customers on its own behalf also registers with the New York State Department of Public Service and gives each customer a standard disclosure statement. No state agency licenses solar installers, electricians or home improvement contractors; the license behind an array’s wiring comes from the city, town, village or county where the job sits. That wiring is built to the electrical standard the state’s Uniform Code brings in, and workers’ compensation is compulsory for covered employers, placed with the New York State Insurance Fund, with an authorized insurer, or through self-insurance the New York State Workers’ Compensation Board approves.
Put plainly, the state regulates the deal and the code, and local governments regulate the person holding the wire. The sections below take each finding with the source’s own words, then practical steps for the owner.
Coverage mechanics that hold in any state are on our solar contractor insurance page and the coverage pages it links to. This page adds the New York layer for a business doing rooftop installation, running panel cleaning and maintenance routes or taking on ground-mount and solar farm construction.
A relationship diagram with a solar job on a New York home at the center. From the job, labeled lines run to each rule it answers to: it is sold under a written contract signed by every party, because the home improvement article covers solar energy systems and wants amendments written and signed as well; that contract must disclose, before work begins, a property or casualty policy covering the scope of the contractor’s or subcontractor’s work; when a provider sells the job on its own behalf to a residential or small commercial customer, the provider registers with the public service department; that provider hands the customer a standard disclosure statement as part of the sales agreement; the wiring is done by an electrician licensed where the job sits, since the state licenses none and cities, towns, villages and counties may; the work is built to the Uniform Code, which brings in the National Electrical Code, while the largest city keeps its own codes; and the crew is covered by compulsory workers’ compensation from the state fund, an authorized insurer or self-insurance the board approves. No figures are shown.
A home contract that has to name the contractor’s insurance
New York reaches solar sales and installation through a statute and a utility commission rule. The General Business Law’s home improvement article names solar energy systems among the home improvements it covers and requires every covered contract to be written, signed and to disclose the contractor’s property or casualty insurance before work starts; the Public Service Commission’s business practices for distributed energy suppliers require a provider selling on-site solar to residential or small commercial customers on its own behalf to register with the Department of Public Service and hand each customer a standard disclosure statement.
The home improvement rules reach any contractor doing covered work on a home for its owner, so a rooftop installer signing a homeowner writes the contract the article prescribes, insurance disclosure included. The registration reaches the business that solicits the customer on its own behalf — a firm installing as a hired contractor for that provider is not itself a provider, though the provider answers for its contractors’ conduct.
Authority: N.Y. Gen. Bus. Law §§ 770(3), 771(1); PSC Case 15-M-0180, Uniform Business Practices for Distributed Energy Resource Suppliers §§ 1, 2D, 3A, 3D
Because the home improvement article counts solar energy systems among the improvements of residential property it covers, an array on a house sits under the same contract rules as any other work on a home. The rule on form leaves no room for a handshake:
“Every home improvement contract subject to the provisions of this article, and all amendments thereto, shall be evidenced by a writing and shall be signed by all the parties to the contract.”
The rule reaches amendments as well. A moved array, an added battery or a panel upgrade agreed on the roof is a change to the contract, and it belongs in writing and signed like the original.
The clause an insurance agency reads with the closest attention is the disclosure the contract must carry:
“Before a contractor or subcontractor begins work on a home, such writing shall disclose to the homeowner the existence of a property and/or casualty insurance policy that covers the scope of such contractor or subcontractor's employment”
The timing is fixed: before the crew begins work on the home. A contract signed weeks before installation day has to be accurate when it is signed and still accurate when the ladders go up.
What the insurance disclosure asks your agent to confirm
The law sets what the contract must disclose, not how to make the disclosure true. These are suggestions, not rules the state has written:
- A policy that fits the work. Ask your agent whether the policy you will name describes solar installation, roof penetrations and electrical tie-ins, not only the trade your business started in. How a liability policy treats damage to the roof or the house is set out on the general liability page.
- Subcontractors before they start. The clause speaks of a subcontractor’s work too. Collect each subcontractor’s certificate of insurance before its people reach the home.
- Renewals and changes. When a policy renews or changes insurer, update the contract template the same week, so no salesperson hands a homeowner a stale disclosure.
- Equipment on site. Agree in writing who bears the risk for modules waiting in the driveway; the tools and equipment page covers stock in transit and on site.
The article is written for residential property, so a job on a warehouse, a school or a farm building falls outside it, and the insurance terms there come from the owner’s contract instead; the umbrella liability page explains how a higher layer answers a contract that asks for more.
When the seller is a provider and the installer is its contractor
The other state rule comes from the Public Service Commission, which sets the business practices for distributed energy suppliers, including on-site solar providers selling to homes and small businesses. Whether your business registers turns on its definition of an on-site provider, an entity
“engaged in soliciting mass market customers for a project or service that involves the installation of distributed generation equipment, such as solar panels, on the property of those mass market customers”
acting
“through its own employees or contractors, on its own behalf rather than as a contractor.”
The customers it has in mind are defined by their utility rate, not by the building:
“A customer that is within a distribution electric utility’s residential or small commercial service class and is not billed based on peak demand.”
A registered provider then hands every customer a standard statement as part of the sale:
“A completed Standard Customer Disclosure Statement shall be provided to all customers of CDG or On-Site Mass Market DG Providers as part of the sales agreement.”
The New York State Department of Public Service takes the registration. For a business that sells its own jobs and also installs for other sellers, the line runs job by job: on its own sales it is the provider, and on a job a provider sold it is the contractor. The rules still reach that contractor indirectly, because the provider answers for its contractors’ conduct and may write that responsibility into the subcontract.
Our suggestions for an installer working under a provider: read the subcontract’s conduct and indemnity clauses with your agent, ask for a copy of the disclosure statement the provider’s customers sign so your crew does not contradict it at the door, and keep any production estimate you supply in writing. When a customer says an estimate misled them and nothing was damaged, the professional liability page explains how a policy treats that claim.
Why the electrician’s license depends on the job’s address
New York has no statewide license for solar installation. The Department of State licenses no electrical contractors, electricians, solar installers or home improvement contractors, and state law hands the licensing of electricians and other trades to cities, towns, villages and counties.
Licensing is set locally instead. The General City Law lets a city examine and license master and special electricians, and cities such as Albany allow electrical work only by an electrician licensed to work in the city, so the license a solar crew needs depends on the city or county where the job sits.
Authority: N.Y. Gen. City Law § 20(27); N.Y. Mun. Home Rule Law § 10(1)(ii)(a)(12); N.Y. Gen. Bus. Law § 771(1)(a)
The power a city uses comes from state law, which lets it enact ordinances
“To examine, license and regulate master and special electricians”
The home improvement article reflects the same gap. Its list of what a contract must contain asks for a license number only where a license applies:
“The name, address, telephone number and license number, if applicable, of the contractor.”
The City of Albany shows how a city fills the space: the city licenses electricians through its Electrical Examining Board, allows electrical work only by an electrician licensed to work in the city, and issues electrical permits only to such electricians, with a temporary license for electricians licensed in municipalities that have reciprocity with the city. Its permit form is blunt about it:
“Please note that electrical work is dangerous and may only be done by an electrician licensed to work in the City of Albany.”
Those local rules govern electrical work, not solar by name, so on an array they reach the wiring, the inverter and the tie-in rather than the racking. For a contractor working across a region, licensing becomes a map you keep yourself:
- For every place where you price a job, find out whether it licenses electricians, whether it honors a license from elsewhere, and who must pull the electrical permit.
- Record which electrician, on your payroll or subcontracted, holds the license for each place, and when it lapses.
How a liability policy treats the electricians you subcontract, and a wiring fault that surfaces after the inspection, is set out on the general liability page.
The Uniform Code, the electrical standard and the arrays it leaves out
New York adopts the National Electrical Code by reference through its Uniform Fire Prevention and Building Code, for the buildings and structures the Building Code covers. The Building Code of New York State, incorporated into the state’s regulations by the State Fire Prevention and Building Code Council, says its electrical chapter and the National Electrical Code govern electrical installations in the buildings it covers, and it sends photovoltaic systems to the National Electrical Code without amending the code’s solar photovoltaic article.
Solar wiring on a building in New York is built to the edition the Uniform Code adopts, enforced by the city, town, village or county that issues the permit. Some work sits outside that rule: a ground-mounted array that is neither attached to nor an appurtenance of a building falls outside the state Building Code, and the Executive Law keeps New York City under its own building codes.
Authority: 19 NYCRR §§ 1220.2, 1221.2; 2025 Building Code of New York State §§ 2701.1, 3111.3 and ch. 35; N.Y. Exec. Law § 383(1)(c)
The building code the State Fire Prevention and Building Code Council adopts hands electrical work to the national standard:
“The provisions of this chapter and NFPA 70 shall govern the design, construction, erection and installation of the electrical components, appliances, equipment and systems used in buildings and structures covered by this code.”
Its list of referenced standards names the edition:
“70—23: National Electrical Code”
and its solar section sends photovoltaic systems to the same place:
“Photovoltaic solar energy systems shall be designed and installed in accordance with this section, the Fire Code of New York State, NFPA 70 and the manufacturer’s installation instructions.”
The solar photovoltaic article of the national code is not amended along the way, so it applies as the adopted edition prints it. The code’s reach has edges, though. The building construction part excludes a certain kind of array outright:
“ground-mounted photovoltaic arrays that are neither a building appurtenance nor are attached to a building shall not be subject to the provisions and requirements of the 2025 BCNYS”
and state law leaves the largest cities their own codes where they already had them:
“the existing building and fire prevention codes shall continue in full force and effect”
In practice, ask before each job whether the array is on or part of a building, whether the job sits inside a city that keeps its own codes, and which local office issues the permit. The Division of Building Standards and Codes develops, administers and supports enforcement of the Uniform Fire Prevention and Building Code and the Energy Code, but the inspector comes from the city, town, village or county, so ask that office which edition its inspectors read before the crew mobilizes. A wiring fault traced to finished work is a general liability question, and a record of the code you built to helps whoever answers it.
Where a New York solar payroll gets its comp coverage
Workers’ compensation is compulsory in New York for the employers its law covers. An employer secures it through the state insurance fund, through a stock, mutual or reciprocal insurer authorized to write the coverage in New York, or by qualifying with the Workers’ Compensation Board as a self-insurer.
A solar contractor with employees carries a workers’ compensation policy from the New York State Insurance Fund or an authorized insurer, or qualifies with the Board to self-insure.
Authority: N.Y. Workers’ Comp. Law §§ 10(1), 50, 76(1), 77
The duty is stated near the top of the comp statute:
“Every employer subject to this chapter shall in accordance with this chapter, except as otherwise provided in section twenty-five-a hereof, secure compensation to his employees”
The New York State Insurance Fund is a creation of that statute, which keeps it going in these words:
“There is hereby continued in the department of labor a fund known as "the state insurance fund", for the purpose of insuring employers against liability for personal injuries or death sustained by their employees”
The New York State Workers’ Compensation Board sums up the choices for employers and describes the fund in its own words:
“Insurance policies can be obtained through a private insurance carrier, State Insurance Fund, or becoming self-insured.”
“NYSIF is a not-for-profit agency of the State of New York that offers workers’ compensation, New York State disability benefits and Paid Family Leave insurance.”
For a solar business the decision deserves a side-by-side look. Have your agent set the fund’s terms beside an authorized insurer’s for the same payroll, and check how each treats crews that move between roofs, ground-mount sites and service calls. Have coverage in place before anyone on the payroll climbs, and collect a certificate from every subcontractor before its people step onto an array. Class codes, subcontractors at audit and crews that cross the border are policy questions, covered on the workers’ compensation page; nothing here describes another state’s law.
New York names a state fund in its comp market, and the State Workers’ Compensation Board is listed below. Neither replaces what OSHA’s Fall Prevention Campaign asks of an employer whose people work at height: plan, provide, train.
Agencies to call before a New York job, and why
The New York State Department of Financial Services is the state’s insurance regulator. Any agency that sells you a policy, this agency among them, can be looked up on NIPR.com.
The other state bodies this page relies on are listed with the part each plays, each link opening the body’s own site:
- New York State Department of State: state licensing of the occupations on its list, none of them electrical, solar or contracting; its Division of Building Standards and Codes administers the Uniform Code
- Division of Building Standards and Codes: develops, administers and supports enforcement of the Uniform Fire Prevention and Building Code and the Energy Code
- State Fire Prevention and Building Code Council: adopts the Uniform Code, including the building code that brings in the National Electrical Code
- Public Service Commission: sets the business practices for distributed energy suppliers, including on-site solar providers selling to homes and small businesses
- New York State Department of Public Service: staff arm of the Public Service Commission; registers on-site and community solar providers and takes customer complaints
- New York State Workers’ Compensation Board: workers’ compensation administration, coverage compliance and self-insurance approval
Missing on purpose: a state board that licenses solar installers, electricians or home improvement contractors. In a normal week the offices a crew deals with are the building and electrical licensing offices of the places where it works.
New York’s leading metros and the counties that form them
The cards below show the largest metropolitan areas with a principal city in New York, as the U.S. Census Bureau delineates them, and the New York counties inside each.
New York-Newark-Jersey City, NY-NJ
Part of this metro lies outside New York; this card lists its New York counties only: Bronx County, Kings County, Nassau County, New York County, Putnam County, Queens County, Richmond County, Rockland County, Suffolk County and Westchester County.
Buffalo-Cheektowaga, NY
Made up of Erie County and Niagara County.
Rochester, NY
Made up of Livingston County, Monroe County, Ontario County, Orleans County and Wayne County.
Albany-Schenectady-Troy, NY
Made up of Albany County, Rensselaer County, Saratoga County, Schenectady County and Schoharie County.
Kiryas Joel-Poughkeepsie-Newburgh, NY
Made up of Dutchess County and Orange County.
Syracuse, NY
Made up of Madison County, Onondaga County and Oswego County.
A metro on these cards is a collection of cities, towns and villages, each free to license electricians its own way. Log the municipality, not just the county, for every job you price, and check its electrician rule and its code before the proposal leaves the office.
Carrying these New York rules into a policy program
The rules above decide what a New York job asks of your paperwork and your crew. The policies that respond when something goes wrong are the ones a solar business carries anywhere, each with its own page:
- The insurance the home contract discloses, roof damage and the electricians you bring in lead to general liability.
- Production estimates in a provider’s sale or your own lead to professional liability.
- The compulsory comp law, whether placed with the state fund or an authorized insurer, leads to workers’ compensation.
- Trucks and trailers hauling modules and racking between jobs lead to commercial auto.
- Meters, lifts and equipment staged at a customer’s home lead to tools and equipment.
- Owner and lender contracts that ask for higher limits lead to umbrella liability.
The weight of each line shifts with the kind of work, and the pages on rooftop installation, panel cleaning and maintenance and ground-mount and solar farm construction treat each on its own terms. When you are ready to price New York jobs, a quote request is the place to start.
State rules decide who may do the work and how; the policies decide who pays when something goes wrong.
- A license, registration or certification is a requirement of the state, not insurance.
A panel for New York in rows. Each row sets a requirement of the state beside the exposure that requirement leaves open and the coverage line that answers it. License to install: No statewide license; the city or county where the array goes up may license the work. It leaves open damage to the roof, the building or a neighbor’s property from the installation work, which General Liability answers. Solar sales and installer rules: The state sets its own rules for solar sellers, installers or providers. It leaves open a design, sizing or output estimate the customer relied on that turns out wrong, which Professional Liability answers. Electrical code: The state names the National Electrical Code in part; local codes govern the rest. It leaves open a wiring or tie-in fault traced back to the work after the job is done, which General Liability answers. Workers’ compensation: Required for covered employers, from the open market or the state fund. It leaves open a crew member hurt on the job, which Workers’ Compensation answers. Notes: A license, registration or certification is a requirement of the state, not insurance. The conclusion reads: State rules decide who may do the work and how; the policies decide who pays when something goes wrong. No figures are shown.
Nearby states we also write
New York coverage, services and state offices
What we insure
Coverage lines
New York solar contractor insurance questions
We install for a solar company that signs the customers. Do we have to register with the New York State Department of Public Service ourselves?
Not as an installer alone. The registration reaches the business that solicits residential or small commercial customers for on-site solar on its own behalf. A firm hired to install for that provider is not itself a provider, though the provider answers for how its contractors behave. Expect its subcontract to pass those practices down to you, and register yourself before your own team starts selling.
What does a New York home solar contract have to say about our insurance?
The home improvement law wants the contract in writing and signed by every party, and before your crew or a subcontractor’s crew begins work on the home, the writing has to disclose that a property or casualty policy covers the scope of that work. Have your agent confirm the policy really describes solar installation, and update the contract template each time the policy renews.
Who on our crew needs a license before we connect an array to a home’s electrical panel?
The state issues no license for that work, so the answer depends on the city or county where the house sits. The City of Albany, for example, allows electrical work only by an electrician licensed to work in the city and issues electrical permits only to such electricians. Ask the local building office who must hold its license, and name that person in the proposal.
We are pricing a ground-mount array in a field away from any building. Does the state building code reach it?
The Uniform Code’s building construction rules leave out a ground-mounted photovoltaic array that is neither attached to a building nor an appurtenance of a building. That does not mean nothing applies: the town or county may have its own permit, zoning or electrical requirements. Ask its code office what it reviews for a free-standing array, and get the answer in writing before the racking order goes in.
Does the state’s Uniform Code govern our jobs in the state’s largest city?
Not necessarily. State law keeps the existing building and fire prevention codes of the largest cities in force unless the code council finds them less stringent than the Uniform Code, so a job in the largest city answers to that city’s own building codes. Before pricing a job there, ask the city’s buildings office which electrical code and which electrician license it requires.
Is the New York State Insurance Fund the only place a New York solar business can buy workers’ compensation?
No. The law lets an employer insure with the state fund, with a stock, mutual or reciprocal insurer authorized to write the coverage in New York, or qualify with the New York State Workers’ Compensation Board to self-insure. The Board describes the fund as a not-for-profit agency of the state. Ask your agent to price the fund and the private market side by side for your crew’s mix of work.
We sell systems to small businesses as well as homeowners. Do the provider rules follow those sales?
They can. The Public Service Commission’s business practices define their customers as those in a utility’s residential or small commercial service class that are not billed on peak demand. A small shop on such a rate counts; a large customer billed on demand does not. Check the customer’s utility bill before deciding which disclosure and registration rules apply.
This page describes insurance for solar contractors operating in this state. It is general information, not legal advice and not a statement of coverage. Licensing, interconnection and code requirements change; verify current requirements with the agency named before relying on them.
Get a quote for your New York solar contracting business
Show us a recent New York home contract, the cities where your electricians hold licenses and whether you sell systems yourself or install for a provider, and we will quote from there.