Solar Contractor Insurance by State
Indiana Solar Contractor Insurance
Indiana leaves trade licensing to its cities and counties, holds solar wiring to an electrical code adopted for the whole state, gives distributed generation customers a right to know what they are buying, and makes workers’ compensation compulsory for covered employers.
No Indiana agency licenses solar installation, and the state licenses no electrical contractors or electricians either, so any license that reaches an array’s wiring comes from the county, city, town or township where the job sits. That wiring is built to the electrical code the Fire Prevention and Building Safety Commission has adopted for the whole state, a distributed generation law gives customers rights to know what the business selling or installing their system is providing, and workers’ compensation is compulsory for the employers the law covers, with no state fund behind it.
Each part of that answer carries a wrinkle. An absent state license does not mean an absent license, the customer-rights law is written for distributed generation rather than for solar by name, and the code in force is older than the edition the commission has voted to put in its place. The sections below take each finding in turn, with the source’s own words where they matter and advice for the owner.
How the policies themselves work for a solar business anywhere is laid out on the solar contractor insurance page and the coverage pages it links to. This page keeps to what is particular to Indiana, whether your business does rooftop installation, runs panel cleaning and maintenance routes or takes on ground-mount and solar farm construction.
A two-column comparison. The left column holds what the state itself sets for a solar contractor: an electrical code adopted for the whole state by the building safety commission, whose solar article applies as the adopted edition prints it; a distributed generation law that gives the customer rights to know the expected output, the costs, whether the provider insures the equipment and the provider’s duties, enforced by the Attorney General; and compulsory workers’ compensation, met through an authorized insurer or the board’s approval to pay benefits directly, with no state fund. The right column holds what the state leaves elsewhere: licensing of the trade, electrical work included, set by the county, city, town or township where the job sits; interconnection and net metering rules from the utility regulator, which fall on the customer and the utility; and the written-disclosure rule the customer-rights law calls for, which does not appear in the Administrative Code. No figures are shown.
Licensing that begins at the county or city line
Indiana has no statewide license for solar installation. The state licenses no electrical contractors, electricians, solar installers or general contractors: none appears on the Indiana Professional Licensing Agency’s list of licensed professions or in the Indiana Code’s title on professions and occupations, and the power to license a trade sits with local government.
Licensing is set locally instead. A county, city, town or township may regulate the occupations worked inside it, and cities such as Lafayette and Terre Haute require a city electrical license before anyone wires a job inside city limits, so the rule for a particular solar job comes from the city or county where it sits.
Authority: IC 36-8-2-10; IC 36-1-2-23
The local power rests on a short line of the Indiana Code:
“A unit may regulate the operation of businesses, crafts, professions, and occupations.”
The same code says what kind of government counts as a unit:
“means county, municipality, or township.”
The Northwestern Indiana Regional Planning Commission has published guidance for the local governments in its region on regulating solar installers. It is a planning body’s guidance, not the law, but it states the gap plainly and names who may fill it:
“The State of Indiana currently does not have a specific certification or licensing program for electricians or for PV solar installers.”
“In the absence of a state regulation in this regard, counties and municipalities with approved building departments have authority to require local certification, registration, or other options.”
The City of Lafayette shows what that power looks like when a city uses it: the city requires an electrical license, or work under a licensed electrician, for any installation, maintenance, alteration or repair on electrical equipment inside the city, and issues separate commercial and residential electrical contractor licenses. Its licensing page puts the rule this way:
“You must hold a valid electrical license or be an electrical journeyman or trainee while employed or supervised by a licensed electrician to perform any installation, maintenance, alteration, or repair on any electrical equipment within the City of Lafayette.”
Notice what that rule is written about. It speaks of electrical work, not of solar, so on a solar job the part it reaches is the wiring and the tie-in. As advice, decide before the bid who on the job will hold the city’s electrical license, or which licensed electrician your crew will work under, and name that person in the proposal.
Where licensing is set locally, careful record-keeping does the work a statewide credential would:
- Ask the building or licensing office where the job sits whether it licenses electrical work or registers contractors, and what it wants on file before a permit issues.
- Keep a file of what each city and county has issued your business and when it lapses. A license from the city where your shop sits says nothing about the township around it.
- When you subcontract the tie-in, ask the electrician for the local license along with the certificate of insurance.
How a liability policy treats the electricians and roofers you subcontract, and damage your crews cause on a roof or in a building, is set out on the general liability page.
A customer-rights law that reaches whoever sells or installs the system
Indiana’s distributed generation law, IC 8-1-40-23, gives a customer that produces distributed generation a set of rights to know about the installation and ownership of the equipment — among them the expected output, all installation costs, whether the provider insures the equipment, and the provider’s duties in installing or removing it — and directs the Attorney General to adopt rules that include written disclosure of those rights by the provider.
Authority: IC 8-1-40-23; IC 8-1-40-3
The law that reaches a solar sale in Indiana is not a solar law by name. It is the Indiana Code’s chapter on distributed generation, and its customer-rights section opens this way:
“A customer that produces distributed generation has the following rights regarding the installation and ownership of distributed generation equipment:”
The rights reach the business that sells or installs a customer’s system, and the Attorney General enforces the section and takes complaints about installation and ownership. The written-disclosure rule the section directs does not appear in the Attorney General’s titles of the Indiana Administrative Code, so the duty rests on the statute’s own list of rights. The law speaks of distributed generation on the customer’s premises, which takes in rooftop and ground-mounted solar, not solar alone.
The rights that follow read like a checklist for a solar proposal. Among them, the customer has these:
“The right to know the expected amount of electricity that will be produced by the distributed generation equipment that the customer is purchasing.”
“The right to know all costs associated with installing distributed generation equipment, including any taxes for which the customer is liable.”
“The right to know if a provider of distributed generation equipment insures the distributed generation equipment against damage or loss”
“The right to know the responsibilities of a provider of distributed generation equipment with respect to installing or removing distributed generation equipment.”
The section then calls for rules to carry it out, among them this:
“including a rule requiring written disclosure of the rights set forth in subsection (a) by a provider of distributed generation equipment to a customer.”
As the finding above records, that disclosure rule has not appeared in the Administrative Code, so the statute’s own list is what a customer, or the Indiana Attorney General, Consumer Protection Division, can hold a seller or installer to. As advice, do not wait for a rule: a signed page in every proposal that answers each right on the list leaves a record of what you told the customer.
Interconnection and net metering sit with a different office: the Indiana Utility Regulatory Commission, utility regulator: net metering, excess distributed generation and interconnection rules, which fall on the customer and the utility. A contractor that prepares that paperwork for a customer is still doing work the customer relies on, and the professional liability page explains how a policy treats a paperwork error that holds up a project.
Writing an Indiana proposal with the rights list in mind
The rights quoted above turn parts of an ordinary proposal into statements a customer is entitled to. None of what follows is a rule the state has adopted; it is advice for the owner whose name is on the proposal.
- The expected output. The estimate in your proposal is more than a sales figure. Say how it was produced and what it assumes about shading, orientation and equipment. If the array falls short and the customer blames the estimate, the dispute starts with what you wrote, and the professional liability page sets out how a policy treats a shortfall claim where nothing was damaged.
- All costs, taxes included. List every cost of installing the equipment, including taxes the customer will owe. A cost that surfaces after signing is a complaint in the making.
- Whether the equipment is insured. Do not answer that from memory. Ask your agent what your own policies do for a customer’s equipment, if anything, and write the answer down. Materials on their way to the roof are covered on the tools and equipment page.
- Installing and removing. Spell out what your business will do when the equipment goes in and when it comes off, including a removal and reinstall for a reroof, and who pays for it.
Indiana’s adopted electrical code and the solar article
Indiana adopts the National Electrical Code statewide through the Fire Prevention and Building Safety Commission’s rule 675 IAC 17-1.8, the Indiana Electrical Code, which the commission lists as currently in effect. The rule amends no part of the code’s solar photovoltaic article. A newer edition has been adopted by the commission and is not yet in effect.
Solar wiring on a building in Indiana is built to the commission’s adopted electrical code, enforced through the state and local building departments, and the solar article applies as the adopted edition prints it. The commission has voted to replace the code with a newer edition, but its own docket shows the replacement still awaiting approval, filing and an effective date.
Authority: 675 IAC 17-1.8; LSA Document #26-62 (proposed 675 IAC 17-1.9)
The adopting rule takes in the national code by reference. Its adoption section names the edition:
“That certain document, being titled as National Electrical Code, 2008 Edition, first printing, published by the National Fire Protection Association”
Its scope section says what the code reaches:
“This code covers: Installations of electrical conductors and equipment within or on Class 1 and Class 2 structures, including industrialized building systems, and other premises wiring covered by rules of the Commission in this title.”
The same section leaves out a utility’s own generation, transmission and distribution installations on property the utility owns, leases or holds by easement. As advice, a builder working at the edge of a utility’s property should settle with the permitting office which side of that line each part of the work falls on.
The adopting rule changes a list of sections of the national code, and none of them sits in the solar photovoltaic article, so that article applies as the adopted edition prints it. As advice, make sure each crew lead knows which edition the inspector is reading from.
The commission’s own table of rules gives the adopted code’s status in a short phrase:
“Currently in Effect”
A replacement is under way. The commission’s rulemaking docket describes it this way:
“The proposed amendments have been drafted to: (1) repeal the 2009 Indiana Electrical Code; and (2) replace the 2009 Indiana Electrical Code with the 2026 Indiana Electrical Code.”
The same docket’s timetable still reads:
“Rule takes effect TBD”
A vote is not an effective date. Until the newer edition is approved, filed and given a date it takes effect, the code in force is the adopted rule quoted above. As advice, ask the permitting office which edition its inspectors apply when a job straddles the change, and if a design leans on a provision found only in the newer edition, settle it with the inspector before the work.
How a liability policy treats a fault in completed wiring that comes to light later is explained on the general liability page.
Workers’ compensation through an authorized insurer or the board’s approval
Workers’ compensation is compulsory in Indiana for employers its law covers. An employer either insures with a company authorized to write the coverage in Indiana or proves to the Worker’s Compensation Board of Indiana that it can pay benefits directly. There is no state fund; coverage comes from the private market.
A solar contractor with employees carries a workers’ compensation policy from an authorized insurer, or qualifies with the Board to pay benefits itself.
Authority: IC 22-3-5-1(a)
The board’s eligibility page states the reach of the requirement:
“The law requires most businesses to have worker’s compensation insurance.”
The statute’s security section then gives an employer a choice of routes. It may
“insure and keep insured the employer's liability under IC 22-3-2 through IC 22-3-6 in some corporation, association, or organization authorized to transact the business of worker's compensation insurance in this state”
or it may
“furnish to the worker's compensation board satisfactory proof of the employer's financial ability to pay direct the compensation in the amount and manner and when due”
The board’s home page settles where the money comes from:
“In Indiana, workers’ compensation benefits are paid by employers, not the State.”
For a solar business, that leaves a direct path. The policy comes from an insurer authorized to write workers’ compensation in Indiana, chosen in the private market, unless the Worker’s Compensation Board of Indiana has accepted the business’s proof that it can pay benefits itself.
How roof crews, ground crews and service technicians are classified, how subcontractors are treated at audit and how a policy follows a crew that travels are policy questions rather than Indiana questions, set out on the workers’ compensation page. As advice, settle before the season who on each job is your employee, and collect a certificate from every subcontractor before its people set foot on an array. Nothing on this page reaches past Indiana’s border; for a job in a neighboring state, check that state’s rules.
Indiana sets no state solar license, so the local file and the Worker’s Compensation Board of Indiana carry much of the paperwork. The work at height still has a federal reference in the OSHA fall-prevention campaign.
Which Indiana office holds each piece
The Indiana Department of Insurance is the state’s insurance regulator. Any agency that sells you a policy, this agency among them, can be looked up on NIPR.com.
The other public bodies behind this page each hold a separate part of the picture. Each link goes to the body’s own site, and each role is given as our research verified it:
- Indiana Professional Licensing Agency: statewide professional licensing; its list carries no electrical, solar or general contractor license
- Fire Prevention and Building Safety Commission: adopts the state’s building, fire and electrical codes, including the Indiana Electrical Code
- Indiana Department of Homeland Security: state fire marshal, building plan review and code enforcement; staffs the building safety commission
- Indiana Utility Regulatory Commission: utility regulator: net metering, excess distributed generation and interconnection rules, which fall on the customer and the utility
- Indiana Attorney General, Consumer Protection Division: consumer protection; enforces the distributed generation customer rights section and receives complaints about installation and ownership
- Worker’s Compensation Board of Indiana: workers’ compensation administration, compliance and self-insurance approval
- Northwestern Indiana Regional Planning Commission: regional planning body; its guidance to local governments on regulating solar installers is cited for the absence of a state license
Absent on purpose: a statewide board that licenses solar or electrical contractors, and a state workers’ compensation fund. In an ordinary week the offices that matter are the building, permitting and licensing departments of the cities and counties where your crews work.
Indiana’s metro areas, county by county
The cards below show the largest metropolitan areas with a principal city in Indiana, as the U.S. Census Bureau delineates them, and the Indiana counties inside each.
Indianapolis-Carmel-Greenwood, IN
Made up of Boone County, Brown County, Hamilton County, Hancock County, Hendricks County, Johnson County, Madison County, Marion County, Morgan County, Shelby County and Tipton County.
Fort Wayne, IN
Made up of Allen County, Wells County and Whitley County.
South Bend-Mishawaka, IN-MI
Part of this metro lies outside Indiana; this card lists its Indiana counties only: St. Joseph County.
Evansville, IN
Made up of Posey County, Vanderburgh County and Warrick County.
Lafayette-West Lafayette, IN
Made up of Benton County, Carroll County, Tippecanoe County and Warren County.
Elkhart-Goshen, IN
Made up of Elkhart County.
Because licensing is set by the city or county where a job sits, a metro area is a set of separate rulebooks rather than a uniform market. As advice, log the county and the city for every job you price, check that place’s rule before the proposal goes out, and do not assume that a license good in a metro’s principal city reaches its suburbs.
Where each Indiana finding meets a coverage line
The findings above say where Indiana’s rules sit. The policies that answer for the work are the ones a solar business carries wherever it works, and each has its own page:
- Local licensing and the electricians you bring in point to general liability, which also takes up finished wiring and damage to the roof or building under the array.
- The customer’s right to know the expected output points to professional liability, for estimates and designs a customer relied on.
- The compulsory comp law points to workers’ compensation, placed with an authorized insurer.
- Trucks and trailers that carry modules and racking between the yard and the job point to commercial auto.
- The customer’s right to know whether the equipment is insured, and your own gear on the way to the roof, point to tools and equipment.
- Contracts that ask for limits above the primary layer point to umbrella liability.
Which of those weigh heaviest depends on the work, and the pages on rooftop installation, panel cleaning and maintenance and ground-mount and solar farm construction take each kind of work on its own terms. When you are ready to put the pieces together for Indiana jobs, a quote request is the place to start.
State rules decide who may do the work and how; the policies decide who pays when something goes wrong.
- A license, registration or certification is a requirement of the state, not insurance.
A panel for Indiana in rows. Each row sets a requirement of the state beside the exposure that requirement leaves open and the coverage line that answers it. License to install: No statewide license; the city or county where the array goes up may license the work. It leaves open damage to the roof, the building or a neighbor’s property from the installation work, which General Liability answers. Solar sales and installer rules: The state sets its own rules for solar sellers, installers or providers. It leaves open a design, sizing or output estimate the customer relied on that turns out wrong, which Professional Liability answers. Electrical code: The state adopts the National Electrical Code statewide. It leaves open a wiring or tie-in fault traced back to the work after the job is done, which General Liability answers. Workers’ compensation: Required for covered employers, bought in the open market. It leaves open a crew member hurt on the job, which Workers’ Compensation answers. Notes: A license, registration or certification is a requirement of the state, not insurance. The conclusion reads: State rules decide who may do the work and how; the policies decide who pays when something goes wrong. No figures are shown.
Indiana coverage, services and state offices
What we insure
Coverage lines
Outside authorities
- Indiana Department of Insurance
- Indiana Professional Licensing Agency
- Worker’s Compensation Board of Indiana
- Indiana Department of Homeland Security
- Fire Prevention and Building Safety Commission
- Indiana Utility Regulatory Commission
- Indiana Attorney General, Consumer Protection Division
- Northwestern Indiana Regional Planning Commission
Indiana solar contractor insurance questions
Is there a statewide Indiana license I can hold that lets my crew install solar anywhere in the state?
No. The Indiana Professional Licensing Agency keeps a list of licensed professions with no solar, electrical or general contractor license on it, and the Indiana Code leaves the regulation of trades to counties, cities, towns and townships. The City of Lafayette, for example, requires an electrical license, or work under a licensed electrician, for electrical work inside the city. Check each place before your crew arrives.
We are bidding an array in a city where we have never pulled a permit. What should we ask its offices?
Ask the building or licensing office whether it licenses electrical work or registers contractors, who on your job must hold that license, what it wants on file before a permit issues, and whether the county adds a rule of its own. Ask while you are still pricing the job, and write the answers into the proposal so the crew lead is not finding out on the roof.
Does Indiana’s distributed generation law reach the proposals our sales team writes?
It can. The customer-rights section reaches the business that sells or installs a customer’s system, and it gives the customer a right to know, among other things, the expected output, all installation costs and whether the provider insures the equipment. The Indiana Attorney General, Consumer Protection Division enforces it. The written-disclosure rule the law calls for is not in the Administrative Code, so write your proposals to the statute’s own list.
Which electrical code will an Indiana inspector hold our solar wiring to?
The code the Fire Prevention and Building Safety Commission has adopted and lists as currently in effect, enforced through state and local building departments. The adopting rule leaves the solar photovoltaic article as the adopted edition prints it. The commission has voted on a newer edition, but its docket shows the replacement still waiting on approval, filing and an effective date, so ask the permitting office when a job falls near the change.
Can a solar business in Indiana get its workers’ compensation from a state fund?
No. Indiana has no state fund. An employer the law covers either insures with a company authorized to write workers’ compensation in Indiana or proves to the Worker’s Compensation Board of Indiana that it can pay benefits directly. For a solar business, that means a policy placed in the private market or self-insurance the board has approved, arranged before anyone on the payroll climbs a ladder.
Who sets the rules for connecting a customer’s array to the grid in Indiana?
The Indiana Utility Regulatory Commission regulates net metering, excess distributed generation and interconnection, and those rules fall on the customer and the utility rather than on the installer. A contractor that prepares the application on a customer’s behalf is still doing work the customer depends on, so check every form before it goes in and keep a copy of everything you submit.
Where can I confirm that the agency quoting my solar business is licensed to sell insurance in Indiana?
The Indiana Department of Insurance regulates insurance in Indiana, and an insurance agency’s license, ours among them, can be looked up on NIPR.com. Ask any agency that quotes your program for its license details and check them before you sign. Because Indiana has no state fund, your workers’ compensation is placed through the private market like the rest of the program.
This page describes insurance for solar contractors operating in this state. It is general information, not legal advice and not a statement of coverage. Licensing, interconnection and code requirements change; verify current requirements with the agency named before relying on them.
Get a quote for your Indiana solar contracting business
Send us the Indiana counties you work in, whether you install, service or build arrays, and how your crew is paid, and we will put a program together around those answers.