Solar Contractor Insurance by State
Minnesota Solar Contractor Insurance
Minnesota treats an array’s modules and wiring as electrical equipment for licensed electrical contractors, adds a residential license for home rooftop contracts, adopts the electrical code statewide, aims its solar consumer rules at other sellers and requires comp of every covered employer.
In Minnesota, the modules of an array are electrical equipment, not just the wire behind them. The Minnesota Department of Labor and Industry counts their placement, positioning and securement, along with all their wiring, as electrical equipment under the State Electrical Code, so the electrical work on an array belongs to an electrical contractor the state licenses, and a company that contracts with a homeowner for a rooftop system holds a state residential building contractor or remodeler license as well. The wiring is built to the electrical code the Board of Electricity adopts for the whole state, the state’s solar consumer rules are written for sellers of community solar garden subscriptions and of solar water heating systems rather than for the contractor, and workers’ compensation is compulsory, with no state fund.
None of those licenses carries the word solar in its name. The state reaches the work through laws written for electricians and for home builders, and the licenses are issued by the state rather than by the city or county where a job sits. Each finding below comes with the source’s own words where they matter, and advice for the owner is marked as advice.
The policies themselves, and how they fit a solar business in any state, are covered on the solar contractor insurance page and the coverage pages it links to. What follows stays with Minnesota, for firms that do rooftop installation, keep up panel cleaning and maintenance contracts or take on ground-mount and solar farm construction.
A two-column comparison. The left column holds the duties that fall on the firm installing a photovoltaic array: electrical work done by an electrical contractor the state licenses, since the modules, their securement and all their wiring count as electrical equipment; a residential building contractor or remodeler license for a company contracting with a homeowner, since roof penetration and racking assembly are listed residential skills; wiring built to the electrical code the Board of Electricity adopts statewide, inspected by the state or by a local government that may set stricter rules; and compulsory workers’ compensation with no minimum number of employees, through an authorized carrier or self-insurance the commissioner of commerce permits, with no state fund. The right column holds the solar consumer rules written for others: information duties owed to community solar garden subscribers by the organization selling the subscriptions, and a seller certification rule for solar collectors and water heating systems that does not apply to systems built to generate electric power. No figures are shown.
Modules, racking and wiring as electrical equipment
Minnesota reaches solar installation through its statewide electrical licensing law. The Department of Labor and Industry treats solar PV systems — modules, arrays and their wiring — as electrical equipment, so the electrical work on an array is performed by an electrical contractor licensed by the commissioner of labor and industry, with licensed electricians or registered workers under their direct supervision.
A solar firm that installs or alters the electrical side of an array works as a licensed electrical contractor, or subcontracts that work to a licensed electrical contractor. A company that contracts with a homeowner for a rooftop system also holds a state residential building contractor or remodeler license, because roof penetration for the array and assembly of its racking are listed residential special skills.
Authority: Minn. Stat. 326B.31, subd. 17; 326B.33, subds. 1, 12, 14; 326B.802, subd. 15; 326B.805, subds. 1, 6
The statute defines the regulated work in broad terms:
“"Electrical work" means the installing, altering, repairing, planning, or laying out of electrical wiring, apparatus, or equipment for electrical light, heat, power, technology circuits or systems, or other purposes.”
and reserves it to licensed contractors and the people who work for them:
“Except as otherwise provided by law, no individual other than an employee, partner, or officer of a licensed contractor, as defined by section 326B.31, subdivision 14, shall perform or offer to perform electrical work with or without compensation unless the individual obtains a contractor's license.”
The Minnesota Department of Labor and Industry applies those words to an array in its solar questions and answers:
“Accordingly, solar PV systems, including the placement, positioning and securement of photovoltaic modules, panels and arrays, and their associated components and all electrical wiring, are electrical equipment under the State Electrical Code.”
“All electrical work that is performed as part of the installation of a solar PV system must be performed by a Minnesota-licensed electrical contractor.”
The Department’s answer reaches past the conductors. Placement, positioning and securement of the modules sit in the same sentence as the wiring, so a crew that only sets and fastens panels is handling what the state calls electrical equipment. As advice, staff every Minnesota array as an electrical job: name the licensed electrical contractor responsible for it, and make sure each person on the crew is licensed or working under the supervision the finding above describes.
- When you subcontract the electrical side, collect the electrical contractor’s state license along with its certificate of insurance, and keep the license and the certificate in the job file.
- Ask the Department about any task on an array you cannot place under a license, and keep its answer in writing.
- Because the license is the state’s, it travels with the firm from county to county. What changes from job to job is who inspects the work, which the code section below takes up.
Damage to a roof, a building or a neighbor’s property during the installation is a liability question, and the general liability page explains how a policy treats it, work by subcontracted electricians included.
Home rooftop contracts and the residential building license
A firm that sells rooftop systems to homeowners meets another state license as well. The residential contractor law lists solar tasks among its special skills. Under residential roofing it names the
“penetration of roof coverings for purposes of attaching a solar photovoltaic system.”
and under the general installation specialties, the
“assembly of the support system for a solar photovoltaic system.”
A business that contracts with an owner to provide those skills on a home falls under the law’s licensing clause:
“A person who meets the definition of a residential remodeler as defined in section 326B.802, subdivision 12, must be licensed by the commissioner as a residential remodeler or residential building contractor.”
The Department’s page on the requirement states the outcome for solar firms. The law
“requires companies that contract with residential homeowners to install solar photovoltaic (PV) systems on homes in Minnesota be licensed as a residential building contractor or remodeler.”
The residential license does not take the place of the electrical license. The Department keeps the installation’s electrical work with a licensed electrical contractor, and a licensed electrician doing licensed work is exempt from the residential license, so the way a firm is organized decides which licenses it holds. The residential law is written for residential real estate; commercial roofs and ground-mount fields still call for the electrical license above.
As advice, map your company before the season: which entity signs the homeowner’s contract, which holds the electrical contractor license, and which crews cut into the roof. If a separate sales company signs homeowners and your firm installs, ask the Department which of you the residential license reaches, and keep its answer with your contracts. Leaks around a penetration are a liability matter, taken up on the general liability page, and the rooftop installation page looks at rooftop jobs on their own terms.
Solar consumer rules for garden subscriptions and water heating systems
Minnesota’s solar consumer rules do not reach the photovoltaic contractor. The community solar garden statute sets disclosure duties and prohibitions for the subscriber organization that sells garden subscriptions, and the state Solar Energy Code’s seller certification rule covers solar collectors and solar water heating systems and expressly excludes systems built to generate electric power.
Authority: Minn. Stat. 216B.1641, subd. 9; Minn. Stat. 216C.25; Minn. R. 1325.1100
Minnesota does have solar consumer rules, but they bind other people in a solar sale. The community solar garden statute places its information duty on the business that sells subscriptions:
“A subscriber organization and a subscriber organization's marketing representatives must make reasonable efforts to provide subscribers with timely and accurate information regarding the community solar garden.”
A separate section sets a disclosure for those who make or sell a solar energy system:
“Manufacturers or retailers of solar energy systems shall disclose to each bona fide potential purchaser of a system the extent to which the system meets or exceeds each quality standard.”
The standards adopted under that section, the Solar Energy Code, are written for solar collectors and water heating, and they say so:
“however, this part does not apply to solar energy systems whose primary purpose is to produce generated electric power.”
The Code’s seller rule speaks to the same equipment:
“every seller of solar collectors and solar water heating systems for installation in the state must provide every bona fide prospective buyer a copy of the certification award issued by the SRCC.”
A firm that sells or installs photovoltaic systems meets its state obligations through the electrical and residential contractor licenses instead, with the written-contract duty the residential license carries. A contractor that builds a large community solar garden owes prevailing wages under the garden statute — a labor duty, not a consumer rule.
For a firm that builds photovoltaic systems, then, the state sets no solar disclosure form, seller registration or installer qualification of its own. Advice still applies where the law is silent. A production estimate, a savings figure or a sizing choice the customer relied on can turn into a dispute with no statute behind it, and the professional liability page explains how a policy treats an estimate that falls short. If your firm builds gardens for a subscriber organization, keep the line between its sales paperwork and your construction contract clear in writing, and keep the payroll records the wage duty calls for. The ground-mount and solar farm construction page covers the contracts a developer brings.
A statewide electrical code with room for stricter local rules
Minnesota adopts the National Electrical Code statewide as the Minnesota Electrical Code, through the Board of Electricity’s rule Minn. R. 1315.0200, which incorporates the current edition by reference for all new electrical wiring and equipment. The rule amends no part of the code’s solar photovoltaic article.
Solar wiring in Minnesota is built to the adopted code, permitted and inspected by the Department of Labor and Industry or by a city or county that runs its own electrical inspection, and the solar article applies as the adopted edition prints it. A local government may set stricter electrical requirements inside its own limits.
Authority: Minn. R. 1315.0200, subp. 1a; Minn. Stat. 326B.35; 326B.36, subd. 6
The Board of Electricity’s rule takes in the national code by reference and names the edition:
“All new electrical wiring, apparatus, and equipment for electric light, heat, power, technology circuits and systems, and alarm and communication systems must comply with the regulations contained in the 2026 edition of the National Electrical Code (NEC)”
The Department gives the date that edition began to govern permits:
“The Board of Electricity has adopted the 2026 National Electrical Code (NEC) with an effective date of Aug. 17, 2026.”
That edition is now in effect, and the rule changes nothing in the code’s solar photovoltaic article, so the article applies as the adopted edition prints it. Who inspects the work is a separate question. The statute lets a local government run its own inspection:
“Any political subdivision or the University of Minnesota may make provision for inspection of electrical installations within its jurisdiction”
and leaves room for a local rule that asks more than the state’s:
“nothing herein contained shall prohibit any political subdivision from making and enforcing more stringent requirements than set forth herein”
As advice, on a job inside a city or county that inspects its own electrical work, ask that office what it adds to the state code before the design is final, and note in the job file which office will inspect. A layout that passed in a neighboring city is not proof it will pass here, and a crew lead who knows which office is coming can have the right paperwork on site. A fault in finished wiring that comes to light after the inspection is taken up on the general liability page.
A comp policy owed whatever the size of the payroll
Workers’ compensation is compulsory in Minnesota for every employer the Act covers, with no minimum number of employees. An employer insures with a carrier authorized to write the coverage in Minnesota or obtains a written order from the commissioner of commerce permitting it to self-insure. There is no state fund; an employer an insurer has refused can apply to the state’s assigned risk plan, which the statute says is not a state agency.
A solar contractor with employees on payroll carries a workers’ compensation policy from an authorized insurer, or through the assigned risk plan after an insurer’s written refusal, or qualifies with the commissioner of commerce to self-insure.
Authority: Minn. Stat. 176.181, subd. 2(a); 79.251, subd. 1(a)(4); 79.252, subds. 1, 3
The workers’ compensation statute states the duty this way:
“Every employer, except the state and its municipal subdivisions, liable under this chapter to pay compensation shall insure payment of compensation with some insurance carrier authorized to insure workers' compensation liability in this state,”
and offers the alternative in the same sentence:
“or obtain a written order from the commissioner of commerce exempting the employer from insuring liability for compensation and permitting self-insurance of the liability.”
The Department adds that size does not matter:
“There is no minimum number of employees an employer must have before insurance is required”
No state fund sells a policy. For an employer a licensed insurer has turned down, the statute sets out a residual route and its purpose:
“The purpose of the assigned risk plan is to provide workers' compensation coverage to employers rejected by a licensed insurance company pursuant to subdivision 2.”
and keeps it outside state government:
“The assigned risk plan shall not be deemed a state agency.”
That route opens after an insurer’s written refusal; it is not where the search for coverage begins. As advice, have a policy bound before anyone new starts on the payroll, part-time help included, and collect a current certificate from each subcontractor before its crew reaches an array. How roof, ground and service crews are classified, and how subcontractors are counted at audit, are set out on the workers’ compensation page. Nothing here reaches past Minnesota’s border; for a job in a neighboring state, check that state’s rules.
Minnesota’s Board of Electricity and Department of Labor and Industry are listed below. OSHA publishes a Fall Prevention Campaign aimed at construction employers, built on three steps: plan, provide, train.
Licensing, inspection and insurance offices in Minnesota
The public bodies behind this page, each linked to its own site, with the part each holds:
- Minnesota Department of Labor and Industry: issues electrical contractor and electrician licenses and the residential building contractor, remodeler and roofer licenses; permits and inspects electrical work; administers workers’ compensation and enforces the coverage requirement
- Board of Electricity: adopts the Minnesota Electrical Code, including any amendments, and the rules on electrical licensing, and issues final interpretations of the code
- Minnesota Department of Commerce: insurance regulator; approves workers’ compensation self-insurance and administers the assigned risk plan
Any agency that sells you a policy, this agency among them, can be looked up on NIPR.com. For a solar firm, the Minnesota Department of Labor and Industry is the office of daily contact: it issues the electrical and residential licenses, and it permits and inspects the work wherever a city or county does not do so itself.
Minnesota counties grouped by Census metro area
The cards follow the metropolitan areas the U.S. Census Bureau delineates around Minnesota’s principal cities, with the Minnesota counties inside each.
Minneapolis-St. Paul-Bloomington, MN-WI
This metro crosses the state line; only its Minnesota counties appear here: Anoka County, Carver County, Chisago County, Dakota County, Hennepin County, Isanti County, Le Sueur County, Mille Lacs County, Ramsey County, Scott County, Sherburne County, Washington County and Wright County.
Duluth, MN-WI
This metro crosses the state line; only its Minnesota counties appear here: Carlton County and St. Louis County.
Rochester, MN
Counties in the metro: Dodge County, Fillmore County, Olmsted County and Wabasha County.
St. Cloud, MN
Counties in the metro: Benton County and Stearns County.
Mankato, MN
Counties in the metro: Blue Earth County and Nicollet County.
Sioux Falls, SD-MN
This metro crosses the state line; only its Minnesota counties appear here: Rock County.
The state licenses travel across these areas unchanged. What can differ inside a metro is the office that inspects the wiring and any stricter rule it keeps. As advice, record the county and the city for every job you price, and confirm before the bid whether the state or the local government will inspect it.
From the license file to the insurance file
The findings above set who may do the work and how. The policies that answer when the work goes wrong each have a page of their own:
- Roof penetrations, racking and the electrical work your licensed contractor or subcontractor performs point to general liability, which also takes up finished wiring.
- Production estimates and system designs a customer relies on, with no state disclosure form to anchor them, point to professional liability.
- The compulsory comp law, with no employee minimum and no state fund, points to workers’ compensation.
- Trucks and trailers hauling modules and racking to the job point to commercial auto.
- Meters, lifts and stock waiting to go up on the roof point to tools and equipment.
- Developer and garden-owner contracts that ask for limits above the primary policies point to umbrella liability.
How much each line weighs depends on the work, and the pages on rooftop installation, panel cleaning and maintenance and ground-mount and solar farm construction take each kind on its own terms. A quote request is the place to begin pricing a Minnesota program.
State rules decide who may do the work and how; the policies decide who pays when something goes wrong.
- A license, registration or certification is a requirement of the state, not insurance.
A panel for Minnesota in rows. Each row sets a requirement of the state beside the exposure that requirement leaves open and the coverage line that answers it. License to install: A state license reaches solar installation. It leaves open damage to the roof, the building or a neighbor’s property from the installation work, which General Liability answers. Solar sales and installer rules: The state’s solar rule does not reach the contractor. It leaves open a design, sizing or output estimate the customer relied on that turns out wrong, which Professional Liability answers. Electrical code: The state adopts the National Electrical Code statewide. It leaves open a wiring or tie-in fault traced back to the work after the job is done, which General Liability answers. Workers’ compensation: Required for covered employers, bought in the open market. It leaves open a crew member hurt on the job, which Workers’ Compensation answers. Notes: A license, registration or certification is a requirement of the state, not insurance. The conclusion reads: State rules decide who may do the work and how; the policies decide who pays when something goes wrong. No figures are shown.
Nearby states we also write
Minnesota coverage, services and state offices
What we insure
Coverage lines
Minnesota solar contractor insurance questions
Does placing and fastening the modules count as electrical work in Minnesota, or only the wiring?
The Minnesota Department of Labor and Industry answers that in its solar questions and answers: the placement, positioning and securement of modules, panels and arrays, with their components and all the wiring, are electrical equipment under the State Electrical Code, and all electrical work on a solar installation is done by a Minnesota-licensed electrical contractor. Staff the whole array as an electrical job, and ask the Department about any task you cannot place.
We sell rooftop systems to homeowners and subcontract the electrical side. Which state license is ours to hold?
A company that contracts with homeowners to install solar on their homes is licensed as a residential building contractor or remodeler, because roof penetration for the array and assembly of its racking are listed residential skills. The Minnesota Department of Labor and Industry still keeps the installation’s electrical work with a licensed electrical contractor, so collect that firm’s license and certificate of insurance before its crew arrives.
A city where we have a job runs its own electrical inspections. Can it ask more of our array than the state code does?
It can. The statute lets a political subdivision provide its own inspection of electrical installations, and it does not stop a political subdivision from making and enforcing requirements stricter than the state’s. Call that city’s inspection office while the design is still on paper, ask what it adds to the adopted code, and note in the job file which office will inspect the work.
We build community solar gardens for a developer. Do the subscriber disclosure duties fall on our company?
The garden statute places its information duty on the subscriber organization and its marketing representatives, the businesses that sell subscriptions, not on the firm that builds the garden. The statute does reach a builder another way: a contractor that builds a large community solar garden owes prevailing wages, a labor duty rather than a consumer rule. Keep payroll records for each garden job ready for review.
Is there a Minnesota quality disclosure we have to hand buyers of our photovoltaic systems?
Not as the state’s rules are written. A statute asks manufacturers or retailers of solar energy systems to disclose how a system measures against quality standards, but the standards adopted under it, the Solar Energy Code, cover solar collectors and water heating and do not apply to systems built mainly to generate electric power. A clear written proposal is still good practice for every sale.
We employ just a part-time helper. Does Minnesota still expect us to carry workers’ compensation?
Yes. The Minnesota Department of Labor and Industry says there is no minimum number of employees before insurance is required. A covered employer insures with a carrier authorized to write workers’ compensation in Minnesota, or holds a written order from the commissioner of commerce permitting self-insurance. There is no state fund, so for a small solar firm the practical route is a policy bound before the helper’s start date.
An insurer has turned down our workers’ compensation application in writing. What comes next for our crew?
The statute provides a residual route: a plan whose purpose is to give coverage to employers a licensed insurer has rejected, and which the statute says is not a state agency. The Minnesota Department of Commerce administers it. Keep the written refusal, apply promptly, and do not let anyone work while the application is pending. Ask your agent to keep looking in the open market at each renewal.
This page describes insurance for solar contractors operating in this state. It is general information, not legal advice and not a statement of coverage. Licensing, interconnection and code requirements change; verify current requirements with the agency named before relying on them.
Get a quote for your Minnesota solar contracting business
List the licenses your firm and its electrical subcontractors hold, the share of your work that goes on homes, and who is on your Minnesota payroll, and a licensed agent will build the program around them.