Solar Contractor Insurance by State
Wisconsin Solar Contractor Insurance
Wisconsin licenses an array’s wiring through its electrical credentials with no solar class, bars cities and counties from adding electrical licenses, asks sellers for a pre-sale form, and makes workers’ compensation compulsory with no state fund.
Wisconsin has no solar license, but it does have a state electrical license that reaches the wiring of an array, and the Legislature has taken away the power of cities and counties to add electrical licenses of their own. The Department of Safety and Professional Services licenses the business as an electrical contractor and the electricians who do the work, the same department adopts the electrical code the wiring is built to, and a solar energy system rule asks every seller to complete a pre-sale form. Workers’ compensation is compulsory for the employers the Act covers, and it comes from the private market, with no state fund.
Parts of that answer come with a limit. Whether a rooftop array needs a building permit that calls for the state’s dwelling contractor credentials is not confirmed, and the solar rule’s duties for anyone other than a seller are not confirmed either. The sections below take each finding in turn, with the source’s own words where they matter and advice for the owner.
How the policies themselves work for a solar business anywhere is laid out on the solar contractor insurance page and the coverage pages it links to. This page keeps to what is particular to Wisconsin, whether your business does rooftop installation, runs panel cleaning and maintenance routes or takes on ground-mount and solar farm construction.
A stack of layers under a Wisconsin solar job, read from the top down. At the top is the electrical contractor license the Department of Safety and Professional Services issues to the business, with licensed or registered electricians doing the wiring under a master electrician, and no limited or solar class. Beneath it is the end of municipal electrical licensing, so a city or county cannot add a license of its own. Next are the dwelling contractor credentials tied to building permits for dwellings, with the question of whether rooftop solar needs such a permit left unconfirmed. Below that is the pre-sale form the solar energy system rule makes mandatory for sellers, beside quality standards the rule only recommends. Then comes the Department’s electrical code chapter, which applies the adopted National Electrical Code to commercial buildings and dwellings and leaves the solar article as printed. At the bottom is compulsory workers’ compensation, met through an authorized insurer or a written order of exemption from the Department of Workforce Development, with no state fund. No figures are shown.
A business license, and a master electrician answerable for the crew
Wisconsin licenses electrical wiring through its electrical credentials; it has no solar license, and the text read names no solar work. The Department of Safety and Professional Services licenses the business that installs, repairs or maintains electrical wiring as an electrical contractor, and licensed or registered electricians do the work under a responsible master electrician. Cities and counties may no longer add their own electrical licenses.
A solar contractor in Wisconsin holds an electrical contractor license from the Department before it installs, repairs or maintains the wiring of a system, and has licensed or registered electricians do that wiring under a master electrician who is responsible for the work. Where a building permit is required for work on a dwelling covered by the Uniform Dwelling Code, the permit holder also needs the Department’s dwelling contractor certification and a dwelling contractor qualifier, so the permit rule for a particular rooftop job depends on the municipality or county that issues the permit.
Authority: Wis. Stat. 101.862; 101.861; 101.82; 101.654; Wis. Admin. Code SPS 305.31, 305.40, 305.41
The license for the business rests on a short statute:
“No person may engage in the business of installing, repairing, or maintaining electrical wiring unless the person is licensed as an electrical contractor by the department.”
The people who do the wiring work under that license, and a master electrician answers for the work of any person who is not a master electrician:
“No person who is not a master electrician may install, repair, or maintain electrical wiring unless a master electrician is at all times responsible for the person’s work.”
The Department of Safety and Professional Services credential rule recognizes classes of electrician, but it recognizes no limited or solar class, so the credential on an array is the ordinary electrical credential. The residential classes are fenced in by the rule’s own words:
“shall be limited to wiring associated with dwellings, dwelling units and detached accessory buildings and structures serving the dwellings or the dwelling units”
That fence matters on a mixed job. As advice, before a proposal names the person who will wire an array on a commercial building or an open field, confirm which class that person holds.
Because the license is a state credential, record-keeping is straightforward:
- Keep the business’s electrical contractor license current and on file with every proposal, and name the master electrician who is responsible for the crew’s wiring.
- When you subcontract the tie-in, ask the electrical contractor for its license along with the certificate of insurance, and for the name of the master electrician on your job.
- Do not assume that a general contractor, roofing or home building credential covers the wiring. It does not replace the electrical contractor license.
How a liability policy treats the electricians and roofers you subcontract, and damage your crews cause on a roof or in a building, is set out on the general liability page.
Why a Wisconsin city or county cannot add an electrical license
Wisconsin has taken local electrical licensing out of the picture, and the statute says so in plain words:
“municipalities may no longer impose any registration, licensing, or certification requirements on electrical contractors, electricians, or electrical inspectors.”
The license is the same between places, so a crew that wires an array in a city does not need an added electrical license to wire an array in the next town. That is a statement about electrical licensing only. A city or county still issues building permits, and the section below takes up what is not confirmed about those permits.
As advice, keep the habit of calling the permitting office before you price a job in a place you have not worked, and ask what it wants on file, who must sign the application, and whether the county adds a step. Write the answers into the proposal so the crew lead is not finding out on the roof.
Dwelling contractor credentials, and a rooftop permit question left unconfirmed
Another state credential sits beside the electrical license, and it is easy to confuse with it. The statute ties it to building permits for work on dwellings:
“no person may obtain a building permit unless the person annually obtains from the department a certificate of financial responsibility”
The credentials are a dwelling contractor certification, held together with a dwelling contractor qualifier certification, and the Department of Safety and Professional Services licenses dwelling contractors. They are tied to building permits for dwellings under the uniform dwelling code.
What this page cannot tell you is whether a rooftop array on a house needs that kind of permit. It is not confirmed, and the answer depends on the municipality or county that issues the permit. The dwelling credentials are a permit rule, not a wiring license, and it is the electrical contractor license from the sections above that reaches the wiring.
As advice, put the question to the permitting office in writing when you price a house job: does this array, on this roof, need a building permit under the dwelling code, and if it does, who must hold the dwelling credentials? Keep the reply with the proposal. A sales rep who tells a homeowner that no permit is needed has made a promise on the strength of an answer nobody has confirmed.
A pre-sale form that every seller of a solar energy system completes
Wisconsin’s solar energy system rule, Wis. Admin. Code ch. SPS 371, issued under the Department of Safety and Professional Services’ authority in s. 101.175, makes pre-sale disclosure mandatory: a seller of a solar energy system completes the Department’s pre-sale information form and presents its information to the prospective buyer in writing and aloud. The quality standards, warranty terms and the Department’s seal of quality in the same chapter are voluntary.
Authority: Wis. Stat. 101.175; Wis. Admin. Code SPS 371.02, 371.03, 371.05
The rule is issued under a section of the statutes whose purpose it states this way:
“The purpose of this section is to establish statewide local energy resource system standards to promote accurate consumer evaluation of local energy resource systems and components thereof.”
The disclosure duty falls on the business that sells a system, which takes in an installer selling a system to a customer; it is a form-and-presentation duty, not a license. A contractor that holds itself out as meeting the chapter’s quality standards does so on that form, and a manufacturer or retailer may ask the Department for a seal of quality. The chapter applies to thermal and photovoltaic systems alike and sets no residential limit in its own terms.
The rule marks which of its provisions bind a seller. The consumer evaluation subchapter, where the pre-sale form lives, is stated as a requirement:
“The provisions of subch. II-Consumer Evaluation are mandatory requirements and shall apply as follows:”
The rule’s scope names the disclosure the subchapter exists to require:
“Requiring sellers to disclose information about the quality of the solar energy systems prior to sale;”
And it tells the seller how to deliver it:
“Present, written and orally, the information required on the pre-sale information form with the prospective buyer present.”
The quality standards in the same chapter are of a different kind. The rule calls them recommended, and ties them to the seller’s own statement on the form:
“are recommended standards and shall apply to those systems the seller identifies on the pre-sale information form as meeting those quality standards.”
Read together, the pre-sale form is a duty and the quality standards are a promise a seller chooses to make. As advice, treat the line on the form that says a system meets the standards as a representation, and do not tick it for a system your crew has not built to them.
Some questions stay open, and this page says so rather than guessing. A duty written for an installer that does not sell, for a lender, for a lessor or for a power purchase provider is not confirmed at the state level. Interconnection rules for a customer’s system sit with the Public Service Commission of Wisconsin, listed with the other offices below. A contractor that prepares interconnection paperwork for a customer is still doing work the customer relies on, and the professional liability page explains how a policy treats a paperwork error that holds up a project.
The Department’s electrical code, which reaches commercial buildings and dwellings alike
Wisconsin adopts the National Electrical Code statewide through the Department of Safety and Professional Services’ rule SPS 316.007, the Wisconsin Electrical Code, and the same chapter serves the Wisconsin Commercial Building Code and the dwelling code. The rule amends no part of the code’s solar photovoltaic article.
Solar wiring on a building in Wisconsin is built to the adopted National Electrical Code as chapter SPS 316 modifies it, and the solar article applies as the adopted edition prints it. The Department’s separate solar energy system rule sends a photovoltaic system’s electrical work to the same chapter.
Authority: Wis. Admin. Code SPS 316.007(1)(a); s. 101.82(1)
The statute directs the Department to write the code:
“Promulgate by rule a state electrical wiring code that establishes standards for installing, repairing, and maintaining electrical wiring.”
The adopting rule incorporates the national code by reference, and its adoption paragraph names the edition:
“NFPA 70 National Electrical Code, (NEC) – 2023, including all Temporary Interim Amendments and Errata prior to January 1, 2025.”
The chapter’s scope section says what it covers:
“Except as provided in sub. (2), this chapter applies to electrical wiring installations.”
Where the Department has written its own rule, that rule wins over the standard it adopts:
“Where any department rule in this chapter differs from a requirement within a standard referenced in this chapter, the department rule shall govern.”
The Department’s solar energy system rule points a photovoltaic installation to this same chapter:
“photovoltaic solar energy systems shall comply with the Wisconsin Electrical Code, ch. SPS 316.”
The chapter changes a listed set of sections of the national code, and none of them sits in the solar photovoltaic article, so that article applies as the adopted edition prints it. As advice, make sure each crew lead knows which edition the inspector is reading from, and settle any design that leans on a department amendment with the inspector before the work.
How a liability policy treats a fault in completed wiring that comes to light later is explained on the general liability page.
A written order of exemption, or a policy from an authorized insurer
Workers’ compensation is compulsory in Wisconsin for the employers the Act covers. An employer insures payment of compensation with an insurer authorized to do business in the state, or obtains the Department of Workforce Development’s written order of exemption by showing it can pay compensation itself. Coverage comes from the private market; there is no state fund that insures employers.
A solar contractor with employees carries a workers’ compensation policy from an authorized insurer, or qualifies with the Department of Workforce Development to pay compensation itself. A contractor that cannot find coverage in the voluntary market may turn to the residual-market arrangement the insurance statutes allow, which is a plan and not a company.
Authority: Wis. Stat. 102.28(2)(a)–(b); 102.04(1); 102.30(1); 619.01(1)(a)
The Department of Workforce Development states the requirement in a sentence on its employer page:
“Wisconsin Employers that meet specific requirements are required to carry Worker's Compensation insurance unless they qualify for Self-Insured status.”
The statute’s security section puts the duty on every employer the Act covers. That employer
“shall insure payment for compensation under this chapter in an insurer authorized to do business in this state.”
The same section gives an employer a way out of the policy:
“The department may grant a written order of exemption to an employer who shows its financial ability to pay the amount of compensation”
The Act leaves the insurance market itself alone:
“This chapter does not affect the organization of any mutual or other insurance company or the right of the employer to insure in mutual or other companies against such liability”
For an employer that cannot find coverage in the voluntary market, the insurance statutes allow the commissioner to create a plan. It is a plan, described here by its function, and not a company:
“the commissioner may by rule either promulgate plans to provide such insurance coverages for any risks in this state that are equitably entitled to, but otherwise unable to obtain, that coverage”
For a solar business, that leaves a direct path. The policy comes from an insurer authorized to do business in Wisconsin, chosen in the private market, unless the Department of Workforce Development has granted the business a written order of exemption.
How roof crews, ground crews and service technicians are classified, how subcontractors are treated at audit and how a policy follows a crew that travels are policy questions rather than Wisconsin questions, set out on the workers’ compensation page. As advice, settle before the season who on each job is your employee, and collect a certificate from every subcontractor before its people set foot on an array. Nothing on this page reaches past Wisconsin’s border; for a job in a neighboring state, check that state’s rules.
Wisconsin’s Department of Safety and Professional Services and Department of Workforce Development are among the bodies below. For employers whose people work from heights, the federal page is OSHA’s Fall Prevention Campaign.
The departments, the commissioner and the commission behind each finding
The Office of the Commissioner of Insurance is the state’s insurance regulator. Any agency that sells you a policy, this agency among them, can be looked up on NIPR.com.
The other public bodies behind this page each hold a separate part of the picture. Each link goes to the body’s own site, followed by its role:
- Department of Safety and Professional Services: licenses electrical contractors, electricians and dwelling contractors, issues the Wisconsin Electrical Code and the building codes, and administers the solar energy system rule
- Department of Workforce Development: administers workers’ compensation, including the written order of exemption from the duty to insure
- Public Service Commission of Wisconsin: utility regulator: interconnection standards for distributed generation facilities, which bind the utility and the facility owner seeking interconnection and not the installer
- Wisconsin Legislature: publishes the Wisconsin Statutes and the Wisconsin Administrative Code
Absent on purpose: a solar license, a municipal electrical license and a state workers’ compensation fund. In an ordinary week the offices that matter are the Department that holds the electrical license, the permitting office in the city or county where the crew works, and the agency that placed your policy.
Metro cards with the Wisconsin counties inside each
The cards below show the largest metropolitan areas with a principal city in Wisconsin, as the U.S. Census Bureau delineates them, and the Wisconsin counties inside each.
Milwaukee-Waukesha, WI
Made up of Milwaukee County, Ozaukee County, Washington County and Waukesha County.
Madison, WI
Made up of Columbia County, Dane County, Green County and Iowa County.
Green Bay, WI
Made up of Brown County, Kewaunee County and Oconto County.
Appleton, WI
Made up of Calumet County and Outagamie County.
Racine-Mount Pleasant, WI
Made up of Racine County.
Eau Claire, WI
Made up of Chippewa County and Eau Claire County.
Because the electrical license is the same in every county, a metro card changes where your crew works and not which electrical credential it needs. What can change from town to town is the building permit. As advice, log the city and county for every job you price, and ask that place’s office what its permit calls for before the proposal goes out.
Where the license, the form and the comp duty meet the coverage pages
The findings above say where Wisconsin’s rules sit. The policies that answer for the work are the ones a solar business carries wherever it works, and each has its own page:
- The electrical contractor license and the electricians under it point to general liability, which also takes up finished wiring and damage to the roof or building under the array.
- The pre-sale form and the output a rep describes point to professional liability, for estimates and designs a customer relied on.
- The compulsory comp law points to workers’ compensation, placed with an authorized insurer.
- Trucks and trailers that carry modules and racking between the yard and the job point to commercial auto.
- Modules and tools on the way to the roof point to tools and equipment.
- Contracts that ask for limits above the primary layer point to umbrella liability.
Which of those weigh heaviest depends on the work, and the pages on rooftop installation, panel cleaning and maintenance and ground-mount and solar farm construction take each kind of work on its own terms. When you are ready to put the pieces together for Wisconsin jobs, a quote request is the place to start.
State rules decide who may do the work and how; the policies decide who pays when something goes wrong.
- A license, registration or certification is a requirement of the state, not insurance.
A panel for Wisconsin in rows. Each row sets a requirement of the state beside the exposure that requirement leaves open and the coverage line that answers it. License to install: A state electrician license exists; the text read names no solar work. It leaves open damage to the roof, the building or a neighbor’s property from the installation work, which General Liability answers. Solar sales and installer rules: The state sets its own rules for solar sellers, installers or providers. It leaves open a design, sizing or output estimate the customer relied on that turns out wrong, which Professional Liability answers. Electrical code: The state adopts the National Electrical Code statewide. It leaves open a wiring or tie-in fault traced back to the work after the job is done, which General Liability answers. Workers’ compensation: Required for covered employers, bought in the open market. It leaves open a crew member hurt on the job, which Workers’ Compensation answers. Notes: A license, registration or certification is a requirement of the state, not insurance. The conclusion reads: State rules decide who may do the work and how; the policies decide who pays when something goes wrong. No figures are shown.
Wisconsin coverage, services and state offices
What we insure
Coverage lines
Wisconsin solar contractor insurance questions
We are wiring an array inside a Wisconsin city that has its own licensing office. Does that city’s license apply to our crew?
Not as an electrical license. The statute says municipalities may no longer impose registration, licensing or certification requirements on electrical contractors, electricians or electrical inspectors, so the license that counts comes from the Department of Safety and Professional Services. Permits are a separate matter, so ask the city’s permitting office what it wants on file before the job, and keep its answer with the proposal.
Does Wisconsin issue a limited or solar-only electrical class for our installers?
No. The Department of Safety and Professional Services credential rule recognizes master, journeyman, registered and apprentice classes, plus residential classes limited to dwellings and their accessory structures, and it holds no solar or photovoltaic class. The business holds the electrical contractor license, and the people doing the wiring hold electrician credentials under a master electrician responsible for their work.
Our company is certified as a dwelling contractor and keeps a qualifier on staff. Can that credential cover the wiring?
Not by itself. The dwelling credentials are tied to building permits for dwellings, while wiring a system takes the electrical contractor license from the Department of Safety and Professional Services. Whether a rooftop array needs that kind of permit is not confirmed, so ask the issuing city or county before you bid, and do not assume that either credential stands in for the other.
We sell hot-water collector systems along with photovoltaic ones. Does the pre-sale form cover them all?
The solar energy system rule applies to thermal and photovoltaic systems alike, and a seller completes the Department of Safety and Professional Services pre-sale information form and presents it to the buyer in writing and aloud. The rule’s quality, warranty and manual standards are recommended and bind a seller only for systems it identifies on the form as meeting them. Train every rep on the presentation.
We finance and lease systems to customers. Does Wisconsin’s solar rule add duties for a lender, lessor or power purchase provider?
Not confirmed at the state level. The pre-sale disclosure falls on the business that sells a system, and no duty written for a lender, lessor or power purchase provider is confirmed, which is not a finding that such a duty does not exist. Have counsel read your lease or purchase agreement against the current rule before your reps present it to a customer.
Our designer asks whether the state changed the solar article of the electrical code. Did it?
The Wisconsin Electrical Code chapter amends a listed set of sections of the National Electrical Code, and none of them is in the solar photovoltaic article, so that article applies as the adopted edition prints it. The Department of Safety and Professional Services rule on solar energy systems also sends a photovoltaic system’s electrical work to the same chapter, so the same drawings can serve either rule.
If we would rather pay injured workers ourselves, who grants the written order that lets us skip a comp policy?
The Department of Workforce Development. An employer shows its financial ability to pay compensation, and the department may grant a written order of exemption. Without that order, the employer insures payment with an insurer authorized to do business in Wisconsin. A contractor that cannot find coverage in the voluntary market can ask its agent about the residual-market plan the insurance statutes allow.
This page describes insurance for solar contractors operating in this state. It is general information, not legal advice and not a statement of coverage. Licensing, interconnection and code requirements change; verify current requirements with the agency named before relying on them.
Get a quote for your Wisconsin solar contracting business
Tell us which Wisconsin metros you work in, whether your crew wires its own arrays or hires an electrical contractor, and whether you sell the systems, and we will build a program around those answers.