Solar Contractor Insurance by State

Wyoming Solar Contractor Insurance

Wyoming licenses the wiring of an array through its electrical contractor license, holds it to the National Electrical Code with the edition not confirmed, has no confirmed state rulebook for solar sellers, and routes workers’ compensation through a state division.

Three workers in hard hats and high-visibility jackets confer in front of a ground-mounted solar array, one holding a tablet.

Wyoming has no solar license, and the chapter that licenses electrical work never mentions solar, so the credential that reaches an array’s wiring is the electrical contractor license the Wyoming Department of Fire Prevention and Electrical Safety issues, with a reach that rests on how the statute defines installing electric equipment. That wiring is held to the National Electrical Code, which the statute makes the standard for electric equipment in or on buildings, although the edition that governs a given job is not confirmed here. A state rulebook for the firms that sell or install systems is not confirmed at the state level. And workers’ compensation is monopolistic and compulsory: a covered employer secures it only from the Wyoming Worker’s Compensation Division, with no private-market route; the statute read does not address self-insurance.

The findings differ in firmness. The electrical license and the comp regime are read from the statutes themselves. The license’s reach to photovoltaic wiring is an inference from a definition, and the seller rule and the code edition are not confirmed. Each section below says which kind of finding it is.

How the policies themselves work for a solar business anywhere is laid out on the solar contractor insurance page and the coverage pages it links to. This page keeps to what is particular to Wyoming, whether your business does rooftop installation, runs panel cleaning and maintenance routes or takes on ground-mount and solar farm construction.

How a Wyoming wiring job moves from the statute’s definition of electrical installation through the licensed contractor and the master electrician, then the city and the state division, to a code edition left open.

A top-to-bottom flow that follows a Wyoming wiring job. It starts at the statute’s definition of installing electric equipment as wiring of equipment and conductors subject to the National Electrical Code; solar is not named, so the reach to photovoltaic wiring is an inference. Next comes the licensed electrical contractor, because licensed contractors install all electrical equipment and the exceptions do not carry over to anyone who subcontracts for an exempt person. Then the master electrician of record, who answers for the code and the department’s rules. Then the city, whose contractor board can ask for its own license beside the state electrical license. Then the state division, because workers’ compensation is monopolistic and the employer holds the division’s statement of coverage before work starts. The flow ends at the code itself: the statute names the National Electrical Code and no edition, and the adopting rule is not confirmed. No figures are shown.

An electrical license that reaches photovoltaic wiring through a definition, not through the word solar

Wyoming licenses electrical work at the state level, and the statute names no solar work; that a solar contractor’s wiring falls under the license is an inference from the statute’s definition of installing electric equipment, stated here as an inference. The Department of Fire Prevention and Electrical Safety licenses electrical contractors, master electricians and journeyman electricians, and the statute has licensed contractors install electrical equipment through licensed electricians or registered apprentices. Wyoming has no separate solar license, and cities and counties license contractors on top of the state credential.

A solar contractor in Wyoming holds an electrical contractor license, keeps a licensed master electrician of record answerable for the work, and has licensed journeyman or master electricians, or registered apprentices working under them, do the wiring. Racking and roofing work is a local matter: a city such as Cheyenne requires its own contractor license, and for electrical work that license depends on the state license.

Authority: W.S. 35-9-102(a)(viii); W.S. 35-9-122; W.S. 35-9-123; W.S. 35-9-125(a); W.S. 16-6-1101

The licensing chapter puts its central duty on the contractor, and the verb is a strong word:

“Licensed electrical contractors employing licensed master or journeymen electricians, or registered apprentice electricians supervised by a licensed master or journeyman electrician shall install all electrical equipment.”

The sentence says electrical equipment, not solar equipment. The reach to a solar crew rests on how the chapter defines the work:

“includes installing, altering and repairing the wiring of apparatus equipment and conductors subject to the National Electrical Code”

Nothing in that definition names photovoltaic equipment, and nothing else in the licensing chapter does. That the wiring of an array counts as wiring of apparatus equipment and conductors subject to the National Electrical Code is a reading of the definition, an inference rather than a sentence in the statute. It is the working rule this page uses for any crew that lands conductors, but it remains an inference. As advice, if your scope is unusual, put a written question to the Wyoming Department of Fire Prevention and Electrical Safety and keep the reply with the contract.

No solar class is among the classes the license program covers. The statute also lists exceptions to the licensed-installer rule, among them an owner’s work on the owner’s own property, and it closes the door on a business that would use them by contract:

“Exceptions shall not apply to anyone who contracts or subcontracts to or for any exempt person, partnership or corporation.”

A customer’s exemption therefore does not help a solar contractor. The license also attaches to a person. The contractor applicant must be, or employ in a full-time capacity, a master electrician, and the statute describes that person this way:

“a licensed master electrician of record who assumes responsibility to ensure that the National Electrical Code, W.S. 35-9-120 through 35-9-130 and applicable rules of the department are adhered to on all electrical work”

As advice, decide before the bid who holds that role for your company, ask the department how the statute limits a master’s service to a contractor, and write the name into the proposal. Keep a roster for every job showing which licensed journeyman or master electrician, or which registered apprentice under supervision, lands each conductor.

How a liability policy treats the electricians and roofers you subcontract, and damage your crews cause on a roof or in a building, is set out on the general liability page.

A city license stacked on the state credential, and a statute that makes local licenses portable

Racking and roofing work is a local matter, and so is the license that governs it. The record’s local example is the City of Cheyenne, where the city’s Contractor Licensing Board licenses contractors in the building trades and requires an electrical contractor to hold the state license together with the city license for each classification. The city’s regulations say it in a sentence:

“Electrical contractors are required to possess a valid State of Wyoming and City of Cheyenne license for each classification.”

That is a city’s rule, offered as an example of how the local layer works and not as a survey of every city and county. The Legislature has also spoken to the movement of local licenses from place to place:

“Each county, city, town and other government entity that issues licenses to contractors shall recognize a license issued to a contractor by another county, city, town or other government entity in Wyoming”

The sentence concerns licenses that local governments issue to contractors. It does not turn a city license into a state license, and it does not touch the state electrical credential. It goes on to set conditions for recognition that this page does not restate. As advice, ask the building or licensing office where the array goes up whether it licenses contractors, whether it recognizes a license you hold from another Wyoming government and on what conditions, and what it wants on file before a permit issues.

Sunlight rights, a siting permit and a net metering chapter, with a seller rule not confirmed at the state level

A Wyoming solar consumer rule for sellers and installers is not confirmed at the state level. The statutes read set no disclosure, contract or qualification duty for the firm that sells or installs a system: the net metering chapter runs between the electric utility and the customer-generator, the Solar Rights Act is property law carried out through local permits, and the county permit for commercial solar facilities is a siting rule. The state’s administrative rules are not confirmed.

A solar contractor in Wyoming meets the obligations confirmed here through the electrical license and local contractor licenses. The net metering chapter requires the customer’s system to meet national electrical, electronics-engineering and testing-laboratory safety and performance standards and lets the utility require isolating switching equipment, which a contractor coordinates with the utility; the chapter puts no duty on the contractor, and whether another state rule does is not confirmed.

Authority: W.S. 37-16-101 through 37-16-104; W.S. 34-22-105; W.S. 18-5-502

The solar-related provisions behind that finding are addressed to others. The net metering chapter runs between the electric utility and the customer-generator, so it speaks to the system a customer uses and to the utility that serves it, not to the firm that sells or installs the system. Whether another state rule does is not confirmed at the state level, because the administrative rules under the chapter are not confirmed here.

The Solar Rights Act is property law, and it carries itself out through local government:

“The local government shall establish permit systems for the use and application of solar energy.”

The permit system it calls for is local, so a seller or installer meets it at the city or county office that issues permits. The county permit for commercial solar facilities is a siting rule:

“It is unlawful to locate, erect, construct, reconstruct or enlarge a facility without first obtaining a permit from the board of county commissioners in the county in which the facility is located.”

The sentence is addressed to whoever locates or builds the facility. The record counts it as a rule for facility owners and developers rather than for the contractor, and the capacity at which a project becomes a facility is not restated here. The finding stays narrow: a rulebook for sellers and installers is not confirmed at the state level, the provisions read do not reach the contractor, and the question is not closed.

A seller in that position can do the protecting itself. As advice, build each proposal on some habits:

  • State how the output estimate was produced and what it assumes about shading, orientation and equipment.
  • List the costs the customer will bear, and say in plain words what your business does and what the utility does.

If a customer relies on an estimate that proves wrong and nothing is damaged, the claim that follows is a professional liability question rather than a general liability claim, and that page sets out how such a policy responds.

A statute that makes the national code the standard and leaves the edition to a rule not confirmed here

Wyoming applies the National Electrical Code statewide by statute, and the Department of Fire Prevention and Electrical Safety lists a newer edition among the codes that apply. The edition and its effective date come from the Electrical Board’s rules, which are not confirmed here. The Department says the state adopts the code without modification.

Solar wiring on a building in Wyoming is built to the National Electrical Code, inspected by the state’s electrical inspectors or by a city or county that has taken over enforcement. Which edition governs a given job is not confirmed here.

Authority: W.S. 35-9-120(a); W.S. 35-9-119(a)(i); W.S. 35-9-121(a); W.S. 37-16-104(a)

The statute’s own standard is short:

“The installation of electric equipment in or on buildings, mobile homes and premises shall be made subject to the applicable minimum requirements of the National Electrical Code.”

Notice what the sentence leaves out. It names the National Electrical Code and no edition, and it draws no line between occupancies or kinds of building. The edition is set by rule, and the adopting rule is not confirmed here. The Department’s rules and statutes page lists the codes the state has adopted, and the electrical entry reads:

“2026 National Electrical Code”

The list entry carries no adoption date or effective date. A list entry points to a rule and is not the rule, so this page does not treat the edition in that entry as the edition in force. The Department’s licensing page adds an agency summary:

“The State of Wyoming adopts the National Electrical Code without modification.”

A summary is not the adopting rule. Whether the rule amends the solar photovoltaic article of the code is neither found nor ruled out. As advice, ask the permitting office which edition its inspector will apply to your permit and whether any amendment touches the photovoltaic article, and put the answer in the job file before the drawings are final.

Who inspects is a separate matter from which code applies. The wiring is inspected by the state’s electrical inspectors or by a city or county that has taken over enforcement, so ask at the start of the job who will inspect, and schedule the visit around the answer. A fault in completed wiring that comes to light later is a general liability matter, and a clean inspection record helps whoever has to answer it.

The division that writes workers’ compensation, and the account behind it

Workers’ compensation in Wyoming is monopolistic. A covered employer secures it only through the state’s worker’s compensation division, within the Department of Workforce Services, which collects the premium into a state account and pays every award from it. The private insurance market does not write it; the statute read does not address self-insurance.

A solar contractor with employees in construction applies for coverage with the division and receives a statement of coverage before it starts work in Wyoming, reports payroll and pays premium to the division, and gets a certificate from each subcontractor showing an account in good standing before the subcontractor starts. A contractor from another state registers with the division and either pays an advance premium deposit, files security, or shows a certificate of coverage.

Authority: W.S. 27-14-207(a); W.S. 27-14-701; W.S. 27-14-108(a)(ii); W.S. 27-14-102(a)(vi); W.S. 27-14-206(b); W.S. 27-14-301(a)

The statute’s name for the body is the name this page uses: Wyoming Worker’s Compensation Division. The definitions section places it inside a department:

“means the worker's compensation division within the department of workforce services”

The statement of intent uses the same name when it speaks of creating it:

“in creating the Wyoming worker's compensation division”

Where the money goes is stated just as directly:

“all money received, earned or collected pursuant to this act shall be credited to the worker's compensation account.”

And money not needed at once is handled by a state officer:

“All money collected and accounted for pursuant to this act not immediately necessary for the purposes of this act shall be invested by the state treasurer”

Those words describe a division of a state department carrying the coverage, a state account credited with the money the Act collects and the state treasurer investing the balance. A solar business therefore has no market of competing quotes to shop. The statute read does not address self-insurance: the sections read give the mandatory route, which is application to the division, and neither allow nor forbid an employer carrying its own risk. As advice, plan on premium unless the division tells you otherwise in writing, and describe your crews to the division accurately so that the payroll is classified the way the work is done.

Applying before the hire, and certificates from the subcontractors whose crews climb with yours

The duty that comes before the work is stated in the registration section. As advice, confirm with the Wyoming Worker’s Compensation Division how it classifies each part of your payroll, from roof crews to ground crews to service technicians. The section reads:

“Any employer subject to this act shall not commence business or engage in work in this state without applying for coverage under this act and receiving a statement of coverage from the division.”

The sentence does not wait for a claim. It bars the work itself until the application is made and the statement of coverage is in hand, so the division is dealt with on the day a hire is planned, not the day someone is hurt.

Subcontractors raise a separate question. For public contract work, the statute has the prime or general contractor secure certification that

“the subcontractor has in good standing an account under this act that covers all coverable employees in the employ of the subcontractor.”

That section sits under public contract work, so whether it reaches a private job is a question for the division. Either way, collect the certificate from every subcontractor before its people set foot on an array.

A contractor from another state registers with the division and either pays an advance premium deposit, files security, or shows a certificate of coverage, as the finding above records. How subcontractors are treated at audit and how a policy follows a crew that travels are policy questions rather than Wyoming questions, set out on the workers’ compensation page. Read it knowing that in Wyoming the buying step runs through the division. Nothing on this page reaches past Wyoming’s border.

Wyoming routes comp through a named state division, the Wyoming Worker’s Compensation Division listed below. Ahead of any hire who will climb, the federal reference is OSHA’s Fall Prevention Campaign.

Electrical inspectors, the division and the insurance department: where each file sits

The public bodies behind this page each hold a separate part of the picture. Each link goes to the body’s own page or file, and each role is stated as the record gives it:

The sellers of insurance are the exception to that division. Any producer firm that sells you a policy, ours among them, can be looked up on NIPR.com. Workers’ compensation is bought through the division rather than through a producer, so the license check applies to the firm that places the rest of your program.

The metros on the Census map, and why the job site still sets the local layer

The cards below show the metropolitan areas with a principal city in Wyoming, as the U.S. Census Bureau delineates them, and the Wyoming counties inside each. The delineation leaves the state a short list, so the cards are short too.

Cheyenne, WY

Made up of Laramie County.

Casper, WY

Made up of Natrona County.

The state electrical license and the division are statewide, so a metro line adds only its counties. Contractor licensing that is local follows the city or county where the array goes up. As advice, log the county and the city for every job you price, and check that place’s rule before the proposal goes out.

Coverage pages that follow the electrical license, the division and the open code question

The findings above say where Wyoming’s rules sit. The policies that answer for the work are those a solar business carries wherever it works, and each has its own page:

  • The electrical license, finished wiring and the electricians you bring in point to general liability, which also takes up damage to the roof or building under the array.
  • Estimates and designs a customer relied on, in a state where a seller rule is not confirmed, point to professional liability.
  • The compulsory comp duty and the division’s coverage statement point to workers’ compensation.
  • Trucks and trailers that carry modules and racking between the yard and the job point to commercial auto.
  • Meters, lifts and stock on the way to a job point to tools and equipment, and contracts that ask for limits above the primary layer point to umbrella liability.

Which of those weigh heaviest depends on the work, and the pages on rooftop installation, panel cleaning and maintenance and ground-mount and solar farm construction take each kind of work on its own terms. When you are ready to put the pieces together for Wyoming jobs, a quote request is the place to start.

Wyoming: what the state sets for solar contractors, what each rule leaves open, and the coverage page that discusses it.
License to install A state electrician license exists; the text read names no solar work
Damage to the roof, the building or a neighbor’s property from the installation work General Liability
Solar sales and installer rules Not confirmed at the state level
A design, sizing or output estimate the customer relied on that turns out wrong
Electrical code Not confirmed at the state level
A wiring or tie-in fault traced back to the work after the job is done
Workers’ compensation Bought from the state fund; the statute read does not address self-insurance
A crew member hurt on the job

State rules decide who may do the work and how; the policies decide who pays when something goes wrong.

  • A license, registration or certification is a requirement of the state, not insurance.
  • Solar sales and installer rules is not confirmed at the state level on this page.
  • Electrical code is not confirmed at the state level on this page.

A panel for Wyoming in rows. Each row sets a requirement of the state beside the exposure that requirement leaves open and the coverage line that answers it. License to install: A state electrician license exists; the text read names no solar work. It leaves open damage to the roof, the building or a neighbor’s property from the installation work, which General Liability answers. Solar sales and installer rules: Not confirmed at the state level. No connector is drawn for this row. Electrical code: Not confirmed at the state level. No connector is drawn for this row. Workers’ compensation: Bought from the state fund; the statute read does not address self-insurance. No connector is drawn for this row. Notes: A license, registration or certification is a requirement of the state, not insurance. Solar sales and installer rules is not confirmed at the state level on this page. Electrical code is not confirmed at the state level on this page. The conclusion reads: State rules decide who may do the work and how; the policies decide who pays when something goes wrong. No figures are shown.

Nearby states we also write

Wyoming solar contractor insurance questions

Our installers handle racking and module placement only. Where does the state electrical license come into our proposal?

Racking is a local matter, but the statute has licensed electrical contractors install all electrical equipment, and its definition of installing it takes in wiring of equipment and conductors subject to the National Electrical Code. Solar is not named, so the reach to photovoltaic wiring is an inference. Put your scope to the Wyoming Department of Fire Prevention and Electrical Safety in writing, and name the licensed electrician who lands the conductors in your proposal.

A city on our route runs its own contractor board. Does its license replace the state electrical license?

No. The City of Cheyenne requires a valid state license and its own city license for each electrical classification, so the local credential sits on top of the state credential. The Legislature also has a local government that issues contractor licenses recognize a license another Wyoming government issued, on conditions the section sets. Ask each city office how that applies before you pull a permit.

The Department lists a newer code edition on its website. Should we draw our array to it?

Treat the edition as not confirmed. The statute makes the National Electrical Code the standard for electric equipment and names no edition, and the page that lists the newer edition prints no adoption date. The adopting rule is not confirmed here. Ask the Wyoming Department of Fire Prevention and Electrical Safety or the inspector which edition applies to your permit, and settle it before the drawings are final rather than at the inspection.

We are based out of state and bringing a crew in for a Wyoming array. What do we file with the division?

The record has a contractor from another state register with the Wyoming Worker’s Compensation Division and then pay an advance premium deposit, file security, or show a certificate of coverage. The coverage statement from the division comes before the work starts. Contact the division before mobilizing, tell it where the contract for hire was made and where your principal place of business is, and keep its answer in the job file.

Our electrical subcontractor says it carries its own coverage. What proof should we collect before its people climb on the array?

Ask for a certificate showing an account in good standing with the Wyoming Worker’s Compensation Division that covers all of its coverable employees. The statute section the record cites sits under public contract work, so ask the division whether it reaches a private job; either way the certificate costs little to collect. File it with the subcontract and check it again before the work resumes after a layoff.

A customer asks what the net metering meter will cost and who pays for the facility. What can our proposal say?

The net metering chapter binds the electric utility and the customer-generator. It says the customer-generator is responsible for all costs associated with its facility and has the utility offer a meter that registers flow in each direction. It puts no duty on the contractor. A state rule for sellers and installers is not confirmed, so write your own plain description of who does what and who pays.

We are proposing a ground-mount array on open land. Does the county permit for solar facilities fall on us?

The statute makes it unlawful to locate, erect, construct, reconstruct or enlarge a facility without a permit from the board of county commissioners. The record counts it as a siting rule on facility owners and developers, not on the contractor. Whether a given array is a facility depends on the statute’s definition, which this page does not restate, so ask the county office and write the answer into the contract.

Who regulates the agency pricing our program, and what can we verify about it before signing?

The Wyoming Department of Insurance is the state’s insurance regulator, and an agency’s license, ours among them, can be looked up on NIPR.com. Ask any agency that quotes your program for its license details. Workers’ compensation is not placed through an agency at all, because the Wyoming Worker’s Compensation Division is the route, so the check applies to the firm that places the rest of your program.

This page describes insurance for solar contractors operating in this state. It is general information, not legal advice and not a statement of coverage. Licensing, interconnection and code requirements change; verify current requirements with the agency named before relying on them.

Get a quote for your Wyoming solar contracting business

Send us the master electrician of record on your crews, the arrays you install, service or build, and the Wyoming payroll you will report, and we will put the rest of the program together around the division’s coverage.