Solar Contractor Insurance by State
Montana Solar Contractor Insurance
Montana licenses the electrical work behind commercial and grid-tied solar through its Department of Labor & Industry, adds a construction contractor license for building work, regulates door-to-door residential solar sales, and makes workers’ compensation compulsory.
The Department of Labor & Industry licenses electrical contractors and electricians in Montana, and the Building Codes Program turns that license into a solar requirement: commercial solar work calls for a licensed electrical contractor, and so does the wiring of a grid-tied system. The statute never names solar, so the reach comes through its definition of an electrical contractor. A construction contractor license from the same Department stands beside it for building and roofing work, and no solar-specialty license exists. Residential systems sold door to door fall under a solar consumer protection law, the electrical code is adopted by the Department’s rule and listed on the program’s page, and workers’ compensation is compulsory, secured through self-insurance, an authorized insurer or a public corporation the Legislature created to give employers an option.
Some findings are stated as not confirmed rather than as settled. Whether any Montana city licenses electricians of its own is not confirmed, the statute contemplating city licenses. Whether the general personal solicitation sales law also reaches solar is not confirmed. Any amendment to the code’s photovoltaic article is not confirmed. The sections below take each finding in turn, with the source’s own words where they matter and advice for the owner.
How the policies themselves work for a solar business anywhere is laid out on the solar contractor insurance page and the coverage pages it links to. This page keeps to what is particular to Montana, whether your business does rooftop installation, runs panel cleaning and maintenance routes or takes on ground-mount and solar farm construction.
A stack of layers under a solar job in Montana, read from the top down. At the top is the electrical contractor license from the Department of Labor and Industry, which the statute does not tie to solar by name but which the Building Codes Program applies to commercial solar work and to the wiring of a grid-tied system. Beneath it is the construction contractor license, which replaced a registration and reaches building and roofing work, with exemptions for a licensed electrician within scope, an independent contractor with no employees and an owner on the owner’s own property. Next is the solar consumer protection law, which binds solar companies and door-to-door sales agents on residential systems only. Below that is the electrical code the Department adopts by rule and the program lists, with any amendment to the photovoltaic article not confirmed. Then comes the permit and inspection, issued by the Department or by a certified county, city or town. At the bottom is compulsory workers’ compensation, met by self-insurance, an authorized insurer or the public corporation the statute creates as an option for employers. No figures are shown.
A statute that bars unlicensed electrical work and a program page that applies it to solar arrays
Montana requires a state electrical contractor license for commercial work and for the wiring of grid-tied systems, and the texts read name no solar work. The Department of Labor & Industry licenses electrical contractors and electricians, and its Building Codes Program says all commercial work requires a licensed electrical contractor and that a grid-tied system needs one for the wiring. A separate construction contractor license from the same Department reaches roofing and other building work. Montana has no solar-specific license.
A solar contractor in Montana holds an electrical contractor license, with a master electrician responsible for the firm, before it wires commercial solar or connects any system to the grid, has licensed electricians do that wiring, and holds the Department’s construction contractor license for the building side of the work unless an exemption applies. A residential job outside the grid-tied case can run on an alternative energy permit.
Authority: 37-68-301; 37-68-102(4)(a); 37-45-201; 37-45-102(1)(a); 37-45-104
The prohibition sits in the chapter on electricians and electrical safety. It speaks of the electrical trades and never of solar:
“A person may not engage in or work at the business or trade of or hold out to the public that the person is an electrician, electrical contractor, residential electrician, journeyman electrician, or master electrician in this state”
What brings an array inside that sentence is the statute’s definition of an electrical contractor, which turns on the wiring and not on the kind of equipment the wiring serves. The contractor
“undertakes or offers to undertake for another the planning, laying out, supervising, and installing or the making of additions, alterations, and repairs in the installation of wiring apparatus and equipment for electric light, heat, and power.”
The Montana Building Codes Program applies that definition to solar in its own pages. For commercial work, it states:
“All commercial work requires a licensed electrical contractor.”
For a new residential building with a solar system, it adds:
“If the system will be grid tied then a licensed electrical contractor is required to perform the needed wiring.”
As advice, name the licensed electrical contractor in the proposal, and make sure the master electrician responsible for that firm is a person who answers for your jobs and not a name on a certificate. If you subcontract the wiring, ask for the license and the certificate of insurance before the electrician’s people reach the site.
The program also issues an alternative energy permit for solar installers who are not electricians. That is a permit for a job, not a credential, and the grid-tied case quoted above still goes to a licensed electrical contractor.
Applicants for the master, journeyman and residential electrician licenses are examined and qualified by the Montana State Electrical Board, which examines and qualifies master, journeyman and residential electrician applicants for the Department’s licenses.
Whether any Montana city or town licenses electricians of its own is not confirmed. The licensing statute contemplates city licenses, so ask the building department of the place where the job sits whether it wants anything beyond the Department’s license, and keep the answer in the bid file.
The construction contractor license that replaced a registration
Beside the electrical license, the Department runs a statewide license for construction contractors through the Montana Construction Contractor License (CCL) Program, which licenses construction contractors, including roofing and other building work. The program page and the Department’s notice to registrants say that the former registration became a license, so this page speaks of a license. The statute’s requirement reads:
“An individual or business entity may not engage in business as a construction contractor without a current license from the department.”
The definition of a construction contractor reaches building, altering, repairing or improving a structure attached to real estate, and its list of the work includes roofing. Rooftop mounting is work on a structure, so a business that mounts arrays on roofs should treat this license as its own question, not the electrician’s. As advice, put the scope of your jobs to the program in writing and keep its reply with the file.
The chapter’s exemptions begin from the electrical license. They reach
“an electrician or plumber, licensed in Montana, operating within the scope of the license”
The exemption list also names an independent contractor with no employees and an owner working on the owner’s own property. A business with a crew on its payroll should not assume that either fits it.
Neither statewide route is a solar-specialty license. The Department’s license pages list the residential electrician, journeyman electrician, master electrician and electrical contractor licenses, and the construction contractor license is a general license. The license application also asks for proof of compliance with the workers’ compensation laws, which the comp section below takes up.
A consumer protection law for door-to-door solar sales agents, residential systems only
Montana’s solar consumer protection law, in the Consumer Protection Act at 30-14-165 and 30-14-166, binds solar companies and the sales agents who sell residential solar energy systems door to door. The agent must give the buyer a written explanation of the right to cancel, a canceled contract cannot be enforced and no claim for labor and materials may be filed on it, and solicitations may not use deceptive statements about cost, financing or terms.
Authority: 30-14-165; 30-14-166
A solar contractor that sells residential systems through door-to-door agents makes sure each agent gives the buyer the capital-letter cancellation notice with room for the buyer’s initials, honors a timely written cancellation, and keeps its sales statements about cost, financing and terms accurate. The law reaches a system a resident uses for personal, family or household purposes; commercial and solar farm work falls outside its definitions.
The definitions decide who the law reaches. In the statute’s words, a solar energy system
“means an assembly of equipment and components that has the primary purpose of converting sunlight into electricity by photovoltaic effect for a resident's use for personal, family, or household purposes.”
And a solar sales agent
“means a person or entity that solicits, offers, negotiates, sells, or executes contracts via door-to-door sales to sell a solar energy system at the direction of, or on behalf of, a solar company.”
The duty that follows from those definitions is a written explanation of the buyer’s right to cancel:
“A solar sales agent shall provide a customer with an explanation of the customer's recission rights written in all capital letters”
The statute then says what a cancellation does. After it, a solar company or a solar sales agent representing a solar company
“may not enforce any terms of the rescinded contract and may not file any claims for labor and materials.”
The same section bars a kind of statement. A solar company or a solar sales agent representing a solar company
“may not conduct solicitations using any deceptive statement concerning the costs, financing, and terms and conditions of the purchase or installation of a solar energy system.”
Net metering sits elsewhere in the code and binds the utility and the customer-generator, so it is not counted here as a seller or installer rule. Whether the general personal solicitation sales law also reaches solar is not confirmed, and this page does not count it.
As advice, treat the cancellation notice as part of the sales kit rather than as paper in the glovebox. Train each agent to hand it over in the form the statute describes, make sure the buyer has space to initial it, and keep a copy with the signed proposal. Keep every statement about cost, financing and terms in your scripts and leaflets something you can support from the contract, because the ban on deceptive statements applies to the solicitation itself. The professional liability page explains how a policy treats an estimate or a promise a customer relied on.
The Building Codes Program’s code page and the rule it points to
Montana adopts the National Electrical Code statewide by rule of the Department of Labor & Industry, and the Montana Building Codes Program lists the edition that is now effective. The statute directs the Department to adopt wiring rules for the state, and the state’s exceptions concern utility signal equipment, refinery premises, mines and low-voltage signal and communications wiring, not ordinary solar installations.
Solar wiring in Montana is built to the adopted National Electrical Code as the Department’s rule amends it, under a state electrical permit from the Building Codes Program or from a certified city, county or town, and inspected by that jurisdiction. Which inspector comes to a job depends on where it sits.
Authority: 50-60-603; 50-60-602; 50-60-604; ARM 24.301.401
The program’s Current Codes page says how the listed codes get their force:
“All of the codes listed below are amended and adopted by: Administrative Rules of Montana (ARM) Title 24, Chapter 301”
The same page prints the electrical code line, edition and date as the program gives them:
“National Electrical Code, 2023 Edition - Effective: September 26, 2026”
Whether the adopting rule amends the photovoltaic article of the code is not confirmed, so a designer should not assume that the article applies exactly as the national code prints it. As advice, ask the inspector for the job’s jurisdiction which amendments it applies before the wiring drawings go out, and make sure each crew lead knows which edition the inspector is reading from.
Who inspects the job, and the installations the electrical part leaves out
Who inspects is a separate question from what the code reaches. On inspection, the statute says that the Department or an authorized representative, or a county, city or town it has certified,
“shall inspect electrical installations, issue electrical permits for these installations, and establish and charge a reasonable and uniform fee for the inspections.”
The program’s electrical permits page puts the practical rule in a sentence:
“State electrical permits are required on all electrical work performed in Montana, except in cities, counties and towns certified to issue electrical permits and conduct inspections.”
The statute’s exceptions are stated apart from that. The electrical installations part does not apply to electrical signal or communications equipment and traffic signals; to street lighting and traffic control devices owned or operated by a public utility, city, county or the state; to electrical installations on the premises of petroleum refineries; to mines and buildings on mine property regulated as mines; or to low-voltage signal and communications equipment and optical fiber cable.
The part’s inspection provisions also do not apply to regularly employed maintenance electricians on their employer’s premises. None of these exceptions is written around ordinary solar work, so a solar crew should expect the electrical code and a permit to apply to its wiring, and ask the permitting office early about anything that touches a utility’s own equipment.
As advice, log for every job whether its jurisdiction is certified, and who the inspector is, before the permit application goes in.
Compulsory comp, and a public corporation the Legislature set up as an option for employers
Workers’ compensation is compulsory in Montana for the employers its Act covers. An employer elects a way to secure it: self-insuring with the Department of Labor & Industry’s approval, insuring with an authorized insurance company, or insuring with the insurer the statute creates as the state’s guaranteed market. Coverage comes from an open market of authorized insurers alongside that statute-created insurer.
A solar contractor with employees elects how to secure workers’ compensation: a policy from an authorized insurer, a policy from the statute-created insurer that must cover any employer that asks, or approval to self-insure. The Department of Labor & Industry’s construction contractor license application asks for proof of compliance with the workers’ compensation laws.
Authority: 39-71-401(1); 39-71-2101(1); 39-71-2201(1); 39-71-2313(1); 39-71-2375(1)
The duty to elect sits at the head of the chapter:
“An employer who has any employee in service under any appointment or contract of hire, expressed or implied, oral or written, shall elect to be bound by the provisions of compensation plan No. 1, 2, or 3”
The plan that runs through the open market is described in the statute as a choice to
“insure the employer's liability to pay the compensation and benefits provided by this chapter with any insurance company authorized to transact such business in this state.”
The statute also creates an insurer of its own. It describes that insurer as an entity
“that is a nonprofit, independent public corporation established for the purpose of allowing an option for employers to insure their liability for workers' compensation and occupational disease coverage under this chapter.”
The insurer is not named on this page, which describes it by what the statute says it does. The statute treats it as an authorized insurer.
For a solar business, the practical result is a choice among routes, not a required source. The Employment Standards Division is the Department’s division of the Department that carries workers’ compensation coverage verification and regulations, so questions about verifying coverage start there. The construction contractor statute lists what the license must include, among it
“proof of compliance with workers' compensation laws;”
How roof crews, ground crews and service technicians are classified, how subcontractors are treated at audit and how a policy follows a crew that travels are policy questions rather than Montana questions, set out on the workers’ compensation page. As advice, settle before the season who on each job is your employee, compare the authorized insurers and the statute-created insurer on your own payroll, and collect a certificate from every subcontractor before its people set foot on an array. Nothing on this page reaches past Montana’s border; for a job in a neighboring state, check that state’s rules.
The Construction Contractor License Program and the Department of Labor & Industry in Montana appear below. A roof crew’s fall protection has its federal reference in OSHA’s Fall Prevention Campaign.
Program, board, division and commissioner: who keeps each Montana file
The Montana Commissioner of Securities and Insurance is the state’s insurance regulator. Any agency that sells you a policy, this agency among them, can be looked up on NIPR.com.
The other public bodies behind this page each hold a separate part of the picture. Each link goes to the body’s own site, and each role is stated briefly:
- Montana Department of Labor & Industry: licenses electrical contractors, electricians and construction contractors, adopts the state electrical code and issues electrical permits through its Building Codes Program, and oversees workers’ compensation compliance
- Montana State Electrical Board: examines and qualifies master, journeyman and residential electrician applicants for the Department’s licenses
- Montana Building Codes Program: issues state electrical permits, inspects electrical installations outside certified local jurisdictions, and publishes the adopted code editions and solar permitting guidance
- Montana Construction Contractor License (CCL) Program: licenses construction contractors, including roofing and other building work
- Employment Standards Division: division of the Department that carries workers’ compensation coverage verification and regulations
- Montana Code Annotated: publishes the state code from which the licensing, consumer protection, electrical code and workers’ compensation statutes are read
No body on that list issues a solar-specialty license. The Department’s electrical and construction contractor licenses are the statewide credentials, and in an ordinary week the offices that matter are the program or the certified local office that issues your permit and the inspector who comes to the job.
County lists behind each Montana metro card
The cards below show the metropolitan areas with a principal city in Montana, as the U.S. Census Bureau delineates them, and the Montana counties inside each.
Billings, MT
Made up of Carbon County, Stillwater County and Yellowstone County.
Bozeman, MT
Made up of Gallatin County.
Missoula, MT
Made up of Mineral County and Missoula County.
Helena, MT
Made up of Broadwater County, Jefferson County and Lewis and Clark County.
Great Falls, MT
Made up of Cascade County.
The state license travels with the contractor, but the permit and the inspection depend on where the job sits, since certified cities, counties and towns issue their own. As advice, log the county and the city for every job you price, find out whether that place is certified, and do not assume that the office that handled a job in a metro’s principal city also handles a job in a county around it.
Which policy page answers which Montana finding
The findings above say where Montana’s rules sit. The policies that answer for the work are the ones a solar business carries wherever it works, and each has its own page:
- The electrical license, the subcontracted wiring and the permit inspection point to general liability, which also takes up finished wiring and damage to the roof or building under the array.
- The cancellation notice, the ban on deceptive statements and the estimates a customer relies on point to professional liability.
- The compulsory comp duty and the license application’s proof of compliance point to workers’ compensation, placed through a route the statute allows.
- Trucks and trailers that carry modules and racking between the yard and the job point to commercial auto.
- Your own gear and materials on the way to the roof point to tools and equipment.
- Contracts that ask for limits above the primary layer point to umbrella liability.
Which of those weigh heaviest depends on the work, and the pages on rooftop installation, panel cleaning and maintenance and ground-mount and solar farm construction take each kind of work on its own terms. When you are ready to put the pieces together for Montana jobs, a quote request is the place to start.
State rules decide who may do the work and how; the policies decide who pays when something goes wrong.
- A license, registration or certification is a requirement of the state, not insurance.
A panel for Montana in rows. Each row sets a requirement of the state beside the exposure that requirement leaves open and the coverage line that answers it. License to install: A state electrician license exists; the text read names no solar work. It leaves open damage to the roof, the building or a neighbor’s property from the installation work, which General Liability answers. Solar sales and installer rules: The state sets its own rules for solar sellers, installers or providers. It leaves open a design, sizing or output estimate the customer relied on that turns out wrong, which Professional Liability answers. Electrical code: The state adopts the National Electrical Code statewide. It leaves open a wiring or tie-in fault traced back to the work after the job is done, which General Liability answers. Workers’ compensation: Required for covered employers, bought in the open market. It leaves open a crew member hurt on the job, which Workers’ Compensation answers. Notes: A license, registration or certification is a requirement of the state, not insurance. The conclusion reads: State rules decide who may do the work and how; the policies decide who pays when something goes wrong. No figures are shown.
Nearby states we also write
Montana coverage, services and state offices
What we insure
Coverage lines
Montana solar contractor insurance questions
Our master electrician has left and nobody on staff holds a license. Can we still take a commercial array in Montana?
Not as the program describes it. The Montana Building Codes Program states that all commercial work requires a licensed electrical contractor, and the licensing statute bars anyone from the electrical trade without a license or permit from the Department. Either hire or contract a licensed electrical contractor before you bid, or leave the commercial wiring out of your scope and say so in the proposal.
We only mount racking and leave all wiring to a subcontractor. Does the construction contractor license still apply to us?
It can. The statute requires a current license before anyone engages in business as a construction contractor, and its definition of the work includes roofing. Its exemptions cover a licensed electrician within the scope of the electrical license, but a racking crew with employees is not that. Put the question to the Montana Construction Contractor License (CCL) Program in writing and keep the reply with your bid.
Does the cancellation notice in the solar buyer law apply when the customer is a warehouse or a ranch operation?
The law’s definitions say otherwise. A solar energy system is equipment on a residential property for a resident’s personal, family or household use, and the sales agent duty attaches to door-to-door sales of that system. Commercial and solar farm work falls outside the definitions. Even so, honest statements about cost and terms are good practice on any proposal, whatever the customer.
A homeowner cancels after we have ordered materials for the job. Can we file a claim on the canceled contract?
The statute says that after a rescission, the solar company or its sales agent may not enforce any terms of the rescinded contract and may not file any claims for labor and materials. As advice, hold material orders until the buyer’s cancellation window has closed, and ask your attorney how your contract treats deposits before you rely on any of this.
The Current Codes page lists an electrical code edition. Does that tell us how the photovoltaic article is amended?
No. The page says the listed codes are amended and adopted by the Department’s administrative rules, but whether the adopting rule amends the photovoltaic article is not confirmed. A designer should not assume the article applies exactly as the national code prints it. Ask the inspector for the jurisdiction of the job which amendments it applies before the wiring drawings go out.
Our crew is working inside a certified city. Who issues the electrical permit there?
The Montana Building Codes Program says state electrical permits are required on all electrical work except in cities, counties and towns certified to issue permits and conduct inspections. In a certified place, then, the local office is the one to call. Everywhere else the Department or its representative issues the permit. Find out which applies before the crew mobilizes, because the answer decides whom you schedule the inspection with.
May a Montana solar crew with employees secure its comp through the insurer the Legislature created?
Yes. The duty to elect a way to secure comp can be met by self-insuring with the Department’s approval, by a policy from any authorized insurer, or by a policy from the public corporation the statute creates as an option for employers. The statute treats that corporation as an authorized insurer. Your agent can compare it with private markets for your payroll and loss history.
This page describes insurance for solar contractors operating in this state. It is general information, not legal advice and not a statement of coverage. Licensing, interconnection and code requirements change; verify current requirements with the agency named before relying on them.
Get a quote for your Montana solar contracting business
Tell us whether your Montana crews wire arrays or subcontract the electrical work, whether you sell door to door, and how your crew is paid, and we will build a program around those answers.