Solar Contractor Insurance by State
Ohio Solar Contractor Insurance
Ohio routes workers’ compensation through a state insurance fund, licenses electrical contractors statewide for projects other than residential buildings, and has not confirmed a state rulebook for solar sellers.
The Ohio rule that leaves a solar business the least room is workers’ compensation: a covered private employer pays into the Ohio State Insurance Fund that the Bureau of Workers’ Compensation administers, or qualifies as a self-insuring employer, and the open market is not part of the picture. The Ohio Construction Industry Licensing Board licenses electrical contractors statewide for construction projects other than residential buildings, and its licensing chapter does not name solar installation. Whether Ohio sets its own rules for solar sellers is not confirmed at the state level, though the Ohio Attorney General enforces general consumer law against them. Wiring on a building under the building code is held to the National Electrical Code, as the code’s referenced-standards rule adopts it.
Each of those answers has an edge worth knowing before a bid goes out. The license is tied to the kind of building, the consumer finding is an open question rather than an absence, and the code finding is stated for the building code and no further. The sections below follow each in turn, with the source’s own words where they matter and advice for the owner whose name is on the proposal.
How the policies themselves work for a solar business anywhere is laid out on the solar contractor insurance page and the coverage pages it links to. This page keeps to what is particular to Ohio, whether your business does rooftop installation, runs panel cleaning and maintenance routes or takes on ground-mount and solar farm construction.
A top-to-bottom flow that follows an Ohio solar job through the state’s rules. It begins with the construction industry licensing board, which licenses electrical contractors for construction projects other than residential buildings; its licensing chapter does not name solar installation. Next is the sales side: whether the state sets its own rules for solar sellers is not confirmed at the state level, and the Attorney General enforces general consumer laws against solar sellers. Then comes the wiring, which the building code holds to the national electrical code through its referenced-standards rule, a finding stated for the building code only. The flow ends at the payroll, where workers’ compensation is monopolistic: covered private employers pay into the state insurance fund, or an employer able to show enough financial ability is granted self-insuring status by the administrator. No figures are shown.
A construction board with an electrical license that stops at the residential line
Ohio licenses electrical contractors statewide through the Ohio construction industry licensing board, for construction projects other than residential buildings. The licensing chapter does not name solar installation.
A solar contractor confirms with the licensing board whether its scope of work on a non-residential project falls in the licensed electrical trade, because the chapter licenses the trade and does not list solar work; a residential building is outside the chapter’s definition of a construction project.
Authority: ORC 4740.01; ORC 4740.13; ORC 4740.02
The statute that backs the license is written as a prohibition on holding yourself out, not only on doing the work:
“No person shall act as or claim to be a type of contractor that this chapter licenses unless that person holds or has been assigned a license issued pursuant to this chapter for the type of contractor that person is acting as or claiming to be.”
Read the verbs. Acting as a licensed type of contractor and claiming to be that kind are treated alike, so a proposal, a website and a truck door all count. As advice, a business that is not licensed for a trade should keep that trade out of its marketing words until the license is in hand.
The chapter then says which licenses the board issues. The definition is a list of trades:
“means a license the Ohio construction industry licensing board issues to an individual as a heating, ventilating, and air conditioning contractor, refrigeration contractor, electrical contractor, plumbing contractor, or hydronics contractor.”
Electrical contractor is among the trades on that list. The list names heating, cooling, refrigeration, plumbing and hydronics beside it, and it does not name solar. That is the whole of what the chapter says on the subject, and this page adds nothing to it.
Where the license applies is set by the chapter’s definition of a construction project:
“a construction project involving a building or structure subject to Chapter 3781. of the Revised Code and the rules adopted under that chapter, but not an industrialized unit or a residential building as defined in section 3781.06 of the Revised Code.”
The definition ends by taking a residential building out of the project. So the statewide license described above is written for building and structure projects other than residential buildings. As advice, sort every job at intake by the kind of building under the array, because the answer to who must hold which license starts there. The Ohio Construction Industry Licensing Board is the body that licenses those trades, and it is the office that can tell you how its chapter treats your scope.
Where the licensing chapter is silent about solar, and what to ask the board
A statute that licenses a trade and says nothing of solar leaves the owner to work out where an array’s wiring falls. The open point comes down to a sentence worth repeating: a solar contractor confirms with the licensing board whether its scope of work on a non-residential project falls in the licensed electrical trade, because the chapter licenses the trade and does not list solar work. This page does not answer that question for you, and no page of ours can.
Put the question to the Ohio Construction Industry Licensing Board in writing, and keep what comes back. A short list of what to ask:
- Whether the scope of work on a non-residential project, from racking to the connection, falls in the licensed electrical trade, and which parts of the scope sit outside it.
- Who on the job must hold the license: the business, a person in charge of the work, or the contractor that hires yours.
- How the board treats a crew that only sets racking and mounts modules while a licensed electrical contractor does the wiring.
- Whether the answer changes when the building is a house, given that the chapter’s definition of a construction project leaves residential buildings out.
The answer matters for more than the permit. If your business subcontracts the electrical work, collect the electrical contractor’s license along with its certificate of insurance and file them together. If your own crew does the wiring, tell your agent what trade license backs it, so the program is built on accurate facts. The general liability page explains how a liability policy treats the electricians you bring in and a fault in completed wiring that comes to light later.
There is also a plain record-keeping point. A licensing board’s view can be given in a phone call and forgotten by the next week, so date the answer, name the person who gave it and attach it to the proposal file. If the board’s position changes, the file shows what you relied on when you bid.
A solar sales rulebook not confirmed, and the Attorney General’s general consumer law
Whether Ohio sets its own rules for solar sellers, installers or providers is not confirmed at the state level.
The Attorney General enforces the state’s general consumer sales and home solicitation laws against solar sellers, which is enforcement of general law, not a solar-specific rule.
The office behind that enforcement is the Ohio Attorney General. Its role, as the page it is cited from states it: consumer protection; enforces the Consumer Sales Practices Act and the Home Solicitation Sales Act against solar sellers. The finding is narrow. It says the Attorney General applies laws written for sales in general to solar sellers, and it says that a rule written for solar sellers specifically is not confirmed at the state level. It does not say such a rule exists, and it does not say there is none.
A business that sells or installs systems should read the distinction carefully. Laws written for sales in general are not a checklist for a solar proposal, which is what a solar-specific disclosure law would be. They reach a seller through the claims it makes and the way it makes them. Treat the proposal as the place those laws will be tested, and write it for a reader who is looking for what you promised.
As advice, build each proposal on some habits:
- State how the output estimate was produced and what it assumes about shading, orientation and equipment, so a shortfall can be traced to a stated assumption rather than to a vague promise.
- List every cost the customer will bear, including any that arrive after installation, and describe in plain words what your business does and what the customer or another party does.
- Keep a signed copy of whatever the customer received, and a dated note of any verbal claim a salesperson made at the door or on the phone.
- Train the sales team on the point that a home visit and a signature can raise consumer-law questions of their own, whatever the electrical license says.
If a customer relies on an estimate that turns out wrong and nothing is damaged, the claim that follows is a professional liability question rather than a general liability claim, and that page sets out how such a policy responds. Nothing here describes an Ohio rule about solar sales; the state-level finding is only that a rule for solar sellers is not confirmed, which is not the same as there being none.
The referenced-standards table that carries the national electrical code
Ohio’s building code adopts the National Electrical Code through its referenced-standards rule, which prints the 2023 edition. The modification the rule states is outside the solar photovoltaic article.
Solar wiring on a building under the Ohio Building Code is built to the National Electrical Code edition the referenced-standards rule prints, with the modification the rule states.
Authority: OAC 4101:1-35-01
The adoption sits in a table of standards the building code incorporates. The row for the national electrical code reads:
“70-23 National Electrical Code (except that section 210.8(F) Exception No. 2 does not expire)”
The row is read across separate cells of the table, the standard’s designation and its title. The edition is whatever the row prints, and the row states an exception to the code’s expiration for a section of the wiring rules. That exception sits outside the solar photovoltaic article, so the article applies as the adopted edition prints it.
The finding is stated for the building code only, and this page goes no further than that. Rules for other kinds of construction are a separate question. As advice, do not treat the finding as covering a job that the building code does not govern; ask the permitting office which electrical code its inspectors apply to that job, and write the answer into the job file before the drawings are final.
Habits that help on any job built to a state-adopted electrical code:
- Make sure every crew lead knows which edition the inspector is reading from, because a design that leans on a newer provision can fail an inspection on an older code.
- Keep the drawings, the equipment listings and the inspector’s sign-off together, since a wiring fault traced back to the work years later is judged against what the code required on the day the job was built.
- When the table row changes, treat it as a trigger to review templates, notes and training, not only the drawings for the next job.
A fault in wiring that comes to light after the job is finished is a general liability matter, and a clear record of the code you built to helps whoever has to answer it.
Premiums into the state fund, or self-insuring status on the administrator’s finding
Workers’ compensation in Ohio is monopolistic. A covered private employer pays premiums into the state insurance fund that the Bureau of Workers’ Compensation administers, or qualifies with the Bureau’s administrator as a self-insuring employer.
A solar contractor with employees in Ohio buys workers’ compensation from the state fund or applies to the Bureau’s administrator for self-insuring status.
Authority: ORC 4123.35(A)–(B); ORC 4121.121(A); ORC 4123.34
Start with the premium duty. The statute’s payment section puts it this way:
“every private employer and every publicly owned utility shall pay annually in the month of June immediately preceding the policy year into the state insurance fund the amount of estimated annual premium the administrator fixes for the employment or occupation of the employer”
Notice who sets the number. The administrator fixes the estimated annual premium for the employment or occupation of the employer, and the employer pays it into the fund ahead of the policy year. A solar business therefore has no market of competing quotes to shop. It has the Ohio State Insurance Fund, and its work starts with telling the Bureau accurately what the business does and what its crews do day to day.
The same section gives a route for the employer that can carry the burden itself:
“upon a finding of such facts by the administrator, may be granted the privilege to pay individually compensation, and furnish medical, surgical, nursing, and hospital services and attention and funeral expenses directly to injured employees or the dependents of killed employees, thereby being granted status as a self-insuring employer.”
The privilege is granted on a finding by the administrator, and the status it confers is that of a self-insuring employer. As advice, treat it as a decision for a business with the financial depth to pay injured workers directly and the administrative capacity to do so. For a business without that depth the fund is the route that matters, and the practical work is getting the payroll description right. The next section turns to the Bureau and what the statute charges it with.
What a monopolistic fund changes in how a solar crew is covered
The Bureau is created by statute and run under an administrator. The creating section reads:
“There is hereby created the bureau of workers' compensation, which shall be administered by the administrator of workers' compensation.”
A separate section charges the Bureau’s board of directors and the administrator with the fund’s soundness:
“to safeguard and maintain the solvency of the state insurance fund and all other funds specified in this chapter”
Those quotes describe the fund as a public function with its own officers. The consequence for a solar business is practical. Asking carriers for competing terms and negotiating a rate is not how comp is bought here, because the administrator fixes the premium. What remains is accuracy and discipline:
- Describe the work to the Bureau as it is done, including roof crews, ground crews and service technicians, so that the employment or occupation the administrator rates matches the payroll.
- Settle before the season who on each job is an employee, and collect a certificate of coverage from every subcontractor before its people climb onto an array.
- Keep the rest of the program in step. The liability, equipment and vehicle lines are placed apart from the fund, and the last section of this page links the pages for each.
- If the business ever weighs self-insuring, take the decision to the administrator’s process early, with the financial records it will want, rather than treating it as a billing choice.
How roof crews, ground crews and service technicians are classified, how subcontractors are treated at audit and how a policy follows a crew that travels are policy questions set out on the workers’ compensation page. Read it with the knowledge that in Ohio the buying step runs through the Bureau. Nothing on this page reaches past Ohio’s border; for a job in a neighboring state, check that state’s rules before the crew leaves the yard.
Ohio’s Bureau of Workers’ Compensation fixes the premium, so buying cover is not where an employer weighs one option against another. Planning work at height is a different question, and the federal reference for it is OSHA’s Fall Prevention Campaign.
The Ohio bodies that license, administer and enforce
The public bodies behind this page are listed here. Each link goes to the body’s own page, and each role is given as the source states it:
- Ohio Construction Industry Licensing Board: licenses electrical, plumbing, heating and cooling, refrigeration and hydronics contractors for construction projects other than residential buildings
- Bureau of Workers’ Compensation: administers the state insurance fund and grants self-insuring employer status through its administrator
- Ohio Attorney General: consumer protection; enforces the Consumer Sales Practices Act and the Home Solicitation Sales Act against solar sellers
Any agency that sells you a policy, ours among them, can be looked up on NIPR.com. Workers’ compensation is the exception to that routine: it is bought from the Ohio State Insurance Fund through the Bureau, so the license check applies to the agency that places the rest of your program.
On an ordinary job the offices you deal with depend on the kind of building. A project other than a residential building touches the licensing board; every job with employees touches the Bureau; and a solar sale, whatever the building, can touch the Attorney General’s consumer protection work. Keeping that division in mind saves a call to the wrong office at a bad time.
Metro cards for Ohio contractors, with the counties each draws on
The cards below show the largest metropolitan areas with a principal city in Ohio, as the U.S. Census Bureau delineates them, and the Ohio counties inside each.
Cincinnati, OH-KY-IN
Part of this metro lies outside Ohio; this card lists its Ohio counties only: Brown County, Butler County, Clermont County, Hamilton County and Warren County.
Columbus, OH
Made up of Delaware County, Fairfield County, Franklin County, Hocking County, Licking County, Madison County, Morrow County, Perry County, Pickaway County and Union County.
Cleveland, OH
Made up of Ashtabula County, Cuyahoga County, Geauga County, Lake County, Lorain County and Medina County.
Dayton-Kettering-Beavercreek, OH
Made up of Greene County, Miami County and Montgomery County.
Akron, OH
Made up of Portage County and Summit County.
Toledo, OH
Made up of Fulton County, Lucas County and Wood County.
The workers’ compensation fund is statewide, and so is the electrical contractor license where it applies, so a metro line here adds only its counties. The rest of the picture varies with the kind of building and the kind of sale. As advice, log the county and the building type for every job you price, and check the permitting office of the place where the array goes up before the proposal leaves your hands.
Policy pages to read after the Ohio findings
The findings above say where Ohio’s rules sit. The policies that answer for the work are the ones a solar business carries wherever it works, and each has its own page:
- The electrical license question and the electricians you bring in point to general liability, which also takes up finished wiring and damage to the roof or building under the array.
- Estimates and designs a customer relied on, in a state where a solar sales rule is not confirmed, point to professional liability.
- The state fund and the self-insuring route point to workers’ compensation.
- Trucks and trailers that carry modules and racking between the yard and the job point to commercial auto.
- Meters, lifts and stock on the way to a job point to tools and equipment.
- Contracts that ask for limits above the primary layer point to umbrella liability.
Which of those weigh heaviest depends on the work, and the pages on rooftop installation, panel cleaning and maintenance and ground-mount and solar farm construction take each kind of work on its own terms. When you are ready to put the pieces together for Ohio jobs, a quote request is the place to start.
State rules decide who may do the work and how; the policies decide who pays when something goes wrong.
- A license, registration or certification is a requirement of the state, not insurance.
- Solar sales and installer rules is not confirmed at the state level on this page.
- In this state, workers’ comp comes from the state fund (or approved self-insurance); we place the rest of your coverage.
A panel for Ohio in rows. Each row sets a requirement of the state beside the exposure that requirement leaves open and the coverage line that answers it. License to install: A state electrician license exists; the text read names no solar work. It leaves open damage to the roof, the building or a neighbor’s property from the installation work, which General Liability answers. Solar sales and installer rules: Not confirmed at the state level. No connector is drawn for this row. Electrical code: The state names the National Electrical Code in part; local codes govern the rest. It leaves open a wiring or tie-in fault traced back to the work after the job is done, which General Liability answers. Workers’ compensation: Bought from the state fund, or self-insured with the state’s approval. No connector is drawn for this row. Notes: A license, registration or certification is a requirement of the state, not insurance. Solar sales and installer rules is not confirmed at the state level on this page. In this state, workers’ comp comes from the state fund (or approved self-insurance); we place the rest of your coverage. The conclusion reads: State rules decide who may do the work and how; the policies decide who pays when something goes wrong. No figures are shown.
Nearby states we also write
Ohio coverage, services and state offices
What we insure
Coverage lines
Ohio solar contractor insurance questions
Can our Ohio solar company buy workers’ compensation from a private insurer instead of the Ohio State Insurance Fund?
Ohio’s regime is monopolistic. The statute has a covered private employer pay premiums into the state insurance fund the Bureau of Workers’ Compensation administers, and the alternative the statute offers is status as a self-insuring employer, granted on the administrator’s finding. A private policy is not a route this page can point you to, so start with the Bureau before anybody goes on the payroll.
Our financial position is strong. Can we pay injured workers directly rather than pay premiums?
Possibly. The statute lets an employer that shows sufficient financial ability to the administrator be granted the privilege to pay compensation directly, which gives it self-insuring status. The grant turns on the administrator’s finding, not on the employer’s own view of its books, so apply to the Bureau of Workers’ Compensation well before the payroll starts and ask what it wants to see.
Does Ohio license solar installers?
The Ohio Construction Industry Licensing Board licenses electrical, plumbing, heating and cooling, refrigeration and hydronics contractors for projects other than residential buildings, and its licensing chapter does not name solar installation. Ask the board in writing whether your scope of work on a non-residential project falls in the electrical trade, and keep the answer in the job file.
We install on houses. Does the electrical contractor license reach that work?
The licensing chapter defines a construction project so that a residential building is outside it. That is a statement about the chapter, not a ruling on what your house jobs need. Ask the board and the permitting office where the home sits what each requires of your crew, and have the answer before you price the job.
Does Ohio have its own consumer rules for solar sellers?
That is not confirmed at the state level. What is confirmed is that the Ohio Attorney General enforces the state’s general consumer sales and home solicitation laws against solar sellers. Because no solar-specific rule is confirmed, write each proposal as if a skeptical customer and a regulator will read it: say how the estimate was produced, list every cost and describe who does what.
Which electrical code do Ohio inspectors apply to our wiring?
The building code adopts the National Electrical Code through its referenced-standards rule, and the edition is printed in the quoted table row on this page. The finding is stated for the building code and goes no further, so for a job that code does not govern, ask the permitting office which electrical code applies before the drawings are final.
Do subcontractors on our roof need their own workers’ compensation?
The statute speaks to employers who pay into the Ohio State Insurance Fund and to those granted self-insuring status; this page does not state how a subcontractor’s crew is treated. As advice, collect a certificate of coverage from every subcontractor before its people set foot on an array, and ask your agent how the policy treats uninsured subcontractors at audit.
How do I confirm that the agency quoting my solar business is licensed to sell insurance?
An insurance agency’s license, ours among them, can be looked up on NIPR.com. Ask any agency quoting your program for its license details and check them there before you sign. Remember that workers’ compensation is bought through the Bureau of Workers’ Compensation rather than through an agency, so the rest of your program is the part an agency places.
This page describes insurance for solar contractors operating in this state. It is general information, not legal advice and not a statement of coverage. Licensing, interconnection and code requirements change; verify current requirements with the agency named before relying on them.
Get a quote for your Ohio solar contracting business
Tell us whether your Ohio jobs are homes or commercial buildings, who holds the electrical license on each crew and what the payroll looks like, and we will build the rest of the program around that.