Solar Contractor Insurance by State
Delaware Solar Contractor Insurance
Delaware reaches solar wiring through the Board of Electrical Examiners’ rule, builds it to the electrical code the Fire Prevention Commission adopts, puts community-owned generating facilities under a Public Service Commission certificate, and makes workers’ compensation compulsory.
Delaware reaches solar wiring through the Board of Electrical Examiners: the Board’s rule lists solar electrical work among the electrical services that need an electrician license, even though the electrical statute never uses the word solar. Beside that license, every contractor holds a business license from the Division of Revenue and registers with the Department of Labor, and neither is a solar credential. Wiring is built to the National Electrical Code as the State Fire Prevention Commission adopts it, with force in every county, city and political subdivision. The state’s own solar-facing rules are a Delaware Public Service Commission certificate that the owner of a community-owned generating facility must hold, and protections for residential subscribers. Workers’ compensation is compulsory, insured with an approved carrier or backed by proof that the employer can pay directly, with no state fund that insures employers.
That summary hides some seams. The license that reaches an array rests on a rule rather than on the statute, the community-energy certificate is held by the facility’s owner and not by the crew that builds it, and a fund appears in the comp chapter that does not insure anyone. The sections below take each finding in turn.
How the policies themselves work for a solar business anywhere is laid out on the solar contractor insurance page and the coverage pages it links to. This page keeps to what is particular to Delaware, whether your business does rooftop installation, runs panel cleaning and maintenance routes or takes on ground-mount and solar farm construction.
A hub-and-spoke diagram with a Delaware solar job and its crew at the center. Labeled lines run out to what the state sets around it. The wiring is done under an electrician license from the Board of Electrical Examiners, whose rule lists solar electrical work although the electrical statute never says solar. Every contractor also holds a business license from the Division of Revenue and a registration with the Department of Labor, and neither is a solar credential. Finished electrical work receives a certificate of inspection from a Board-licensed inspection agency before the utility connects service. The wiring is built to the National Electrical Code as the State Fire Prevention Commission adopts it, with the force of law in every county, city and political subdivision. A community-owned facility must hold a certificate to operate from the Public Service Commission, held by the facility owner and not by a rooftop seller or installer. The payroll is insured with an approved carrier or backed by proof of ability to pay, and no state fund insures employers. No figures are shown.
A solar reach that rests on the Board’s rule, not on the electrical statute
Delaware licenses solar wiring through the Board of Electrical Examiners. An electrician license is required by statute, and the Board’s rule names solar electrical work among the work it covers. Every contractor also holds a state business license from the Division of Revenue and registers with the Department of Labor, and neither is a solar credential.
A solar contractor in Delaware has its wiring done under a master electrician or another licensed electrician, holds a contractor business license, registers with the Department of Labor’s Office of Contractor Registration before work starts, and has the electrical work inspected by a Board-licensed inspection agency before the utility connects service.
Authority: 24 Del. C. §§ 1402, 1407, 1420; 24 DE Admin. Code 1400, section 1.1; 30 Del. C. §§ 2501–2502; 19 Del. C. §§ 3602–3605
The electrician license begins with a prohibition. The electrical licensing chapter bars the practice of providing electrical services without a license, in these words:
“No person shall engage in the practice of providing electrical services or hold himself or herself out to the public in this State as being qualified to act as a licensed electrician”
The chapter’s definition of a master electrician says what the broadest license covers:
“to plan, estimate, layout, perform or supervise the installation, erection or repair of any electrical conductor, molding, duct, raceway, conduit, machinery, apparatus, device or fixture for the purpose of lighting, heating or power in any structure.”
The word solar appears in neither provision, and the chapter never uses it. The statute speaks of lighting, heating or power in any structure, and it is the Board of Electrical Examiners’s rule that names the work. Its definition of electrical services includes solar electrical work in a list:
“for the purpose of lighting, heating, or power in or on any structure or for elevators, swimming pools, hot tubs, electric signs, air conditioning, heating, refrigeration, oil burners, solar electrical work, generators, windmills”
So the solar reach rests on the rule, not on the chapter. That matters when a customer, an inspector or a competitor asks what authorizes a crew to wire an array: the answer is the license the statute requires, read with the rule that lists the work. The Board licenses electricians and electrical inspection agencies; its rule names solar electrical work among the work it covers. The Residential Electrician page of the Division of Professional Regulation puts the requirement in an agency’s own words, which are a summary and not the law:
“To perform electrical services in Delaware, you are required to hold a Delaware professional license as an electrician.”
What the record does not show is a solar contractor license. The Division of Professional Regulation staffs the professional licensing boards, including the electrical board; its list of boards carries no solar board. Whether any other part of the Delaware Code creates a solar contractor license is not confirmed here, and nothing quoted on this page points to such a license.
As advice:
- Decide before the bid which licensed electrician will do the array wiring and the tie-in, and name that person in the proposal. Keep a copy of the license in the job file.
- When you subcontract the electrical side, ask for the electrician’s license along with the certificate of insurance, and file them together.
How a liability policy treats the electricians you bring in and damage your crews cause on a roof or inside a building is set out on the general liability page.
The business license and the registration every contractor holds, solar or not
The electrician license is not the only credential on a Delaware job. General construction credentials sit beside it, and the record is clear that they are not solar credentials. Begin with the contractor business license, which the Code ties to the Division of Revenue:
“Any person desiring to engage in business in this State as a contractor shall obtain a license upon making application to the Division of Revenue”
The Division of Revenue issues the contractor business license every contractor needs. Next comes the registration with the Department of Labor’s Office of Contractor Registration, which registers construction contractors with the Department of Labor before they start work. The Contractor Registration Act states the duty in a short sentence:
“A contractor must register under this chapter before performing construction services or maintenance.”
The registration application also asks for proof of Delaware workers’ compensation insurance, a point the comp section below returns to. As advice, keep the business license and the registration on the same renewal calendar as the electrician license so that a lapse in any of them does not surprise you on the day a permit is due.
A further state document turns up in searches for home improvement rules. The Delaware Department of Justice, Consumer Protection Unit enforces the Consumer Fraud Act and its Home Improvement Services Regulation for residential home improvement contracts. The regulation’s scope section opens this way:
“This regulation of the Consumer Fraud Act covers certain unlawful practices covering home improvement transactions”
That is a conduct rule for residential transactions. It does not say solar, and it is not a registration, so this page does not treat it as a solar credential.
The inspection certificate that stands between a finished array and the meter
Finished wiring has a further state-level step. The electrical licensing chapter requires a certificate of inspection for electrical work unless the work is specifically exempt:
“All electrical work performed in this State, unless specifically exempt, shall receive a certificate of inspection issued by a Board-licensed inspection agency.”
The license finding above ties that certificate to the utility: the electrical work is inspected by a Board-licensed inspection agency before service is connected. The Board licenses inspection agencies as well as electricians, so the body that licenses the wiring also licenses the agency that inspects it.
As advice, treat the inspection as a scheduled stage of the job: ask the agency what it wants on site, build its lead time into the customer’s expectations, and keep the certificate in the closeout file. How a liability policy treats a fault that surfaces in finished wiring after the work is accepted is explained on the general liability page.
Community-owned facilities: whose certificate it is, and what the consumer rules reach
Delaware regulates community solar and other community-owned generation through the Public Service Commission. A community-owned energy generating facility must obtain a certificate to operate before it serves customers, and the same law protects residential subscribers from credit checks and upfront enrollment fees. Net metering is open to customers who own, lease or contract with a third party for a generating facility.
A solar farm builder or developer that delivers a community-owned project builds it for an owner that must hold the Commission’s certificate to operate, with an interconnection study or agreement and proof of site control in hand, before subscribers are served. The Commission’s net metering rules do not set an installer duty.
Authority: 26 Del. C. § 1014(d), (f)(12); 26 Del. C. § 1022(c)
For a contractor building a community project, the rule that matters is a registration, and it sits on the owner. The Commission’s certificate to operate is a condition of serving customers:
“A community-owned energy generating facility seeking to provide service to customers must apply for and obtain a certificate to operate from the Commission”
The same provision makes interconnection part of what the owner must show:
“A completed interconnection study or signed interconnection agreement with the electric distribution company.”
The certificate is held by the facility owner, not by a rooftop seller or an installer. A firm that builds the project for the owner is not the holder, which is why the record types this as a provider registration and not as an installer qualification. As advice, ask the owner for proof that the certificate, the interconnection study or agreement and proof of site control are in hand before your crew mobilizes, and write that request into your contract. If a project stalls for want of a certificate, your schedule stalls with it.
The consumer protections in the same law are written for residential subscribers and fall on the facility and on any subscription coordinator:
“No community-owned energy generating facility or subscription coordinator may require residential subscribers to undergo a credit check or pay upfront enrollment fees.”
Net metering is a separate matter and sits with the same Delaware Public Service Commission, which utility regulator: net metering rules and the certificate to operate for community-owned energy generating facilities. The statute directing its rules describes who may take net metering this way:
“rules and regulations that provide for net energy metering for customers who own and operate, lease and operate, or contract with a third party that owns and operates an electric generation facility”
That language names leases and third-party ownership. The Commission’s net metering rules do not set an installer duty, and nothing in the provisions quoted here sets a seller duty; anything further about solar sellers at the state level is not confirmed here. A contractor that prepares interconnection or enrollment paperwork for a customer is still doing work the customer relies on, and the professional liability page explains how a policy treats an error that holds up a project.
A commission regulation that makes the national code law in every county
Delaware adopts the National Electrical Code statewide through the State Fire Prevention Commission’s regulation, which has the force and effect of law in every county, city and political subdivision. The regulation adopts the code in its entirety and amends no part of the solar photovoltaic article.
Solar wiring on a building in Delaware is built to the National Electrical Code edition the State Fire Prevention Commission adopts, which licensed electricians are required to follow and which the electrical inspection agencies inspect against. A city or county may add stricter local standards.
Authority: 1 DE Admin. Code 701, sections 1.1, 1.2 and 3.1.42; 24 DE Admin. Code 1400, section 1.2
The adopting instrument is a regulation of the State Fire Prevention Commission, not a statute. Its adoption section gives it the force of law across the state’s local governments:
“which shall have the force and effect of law in the counties, cities, and political sub-divisions of this State.”
The National Electrical Code appears on the regulation’s list of adopted codes and standards, edition included:
“NFPA 70, National Electrical Code, 2023”
The regulation’s effective-date section reads:
“This regulation will become effective January 1, 2026.”
The regulation’s text contains no amendment to the solar photovoltaic article of the code, so that article applies as the adopted edition prints it. The Board’s rule then ties its licensees to the Commission’s choice:
“The version of the NEC applicable to a particular project is determined by the Delaware Fire Prevention Commission.”
Read together, the Commission sets the code, the Board’s rule requires licensees to work to it, and the inspection agencies inspect against it. A city or county may add stricter local standards, so the state code is a floor for the design, not a promise about every permit office. The State Fire Marshal state fire code administration; announced the new edition of the fire prevention regulations.
As advice, give each crew lead the edition and the effective date from the regulation, and ask the permitting office in each place you work whether it enforces anything stricter. Nothing here reaches past Delaware’s border; for a job across a state line, check that state’s own rules.
Compulsory comp with an approved insurer, and a fund that reimburses carriers
Workers’ compensation is compulsory in Delaware for employers the chapter covers. An employer either insures with a company the Department of Labor approves and the state authorizes to write the coverage, or proves to the Department that it can pay compensation directly. There is no state fund that insures employers; coverage comes from the private market.
A solar contractor with employees carries a Delaware workers’ compensation policy from an authorized insurer, or qualifies with the Department of Labor to pay compensation itself. The contractor registration application asks for proof of that coverage.
Authority: 19 Del. C. §§ 2371, 2372(a); 19 Del. C. § 3605(b)
The duty is stated for every employer the chapter covers:
“Every employer to whom this chapter applies shall insure the payment of compensation to the employees, or their dependents, in the manner provided in § 2372 of this title.”
The security section then gives the employer its routes. It may
“insure and keep insured the employer’s liability for compensation in some corporation, association or organization approved by the Department and authorized to transact the business of workers’ compensation insurance in this State”
or it may
“or shall furnish to the Department satisfactory proof of the employer’s financial ability to pay directly the compensation”
The chapter does create a fund, and a reader skimming it might take that for a state insurer. It is not. The fund’s stated purpose is narrow:
“is created for the purpose of making payments under § 2327, § 2334, or § 2347 of this title by any insurance carrier.”
It reimburses carriers for particular payments, issues no policy and insures no employer, so it is not a route to coverage for a solar business. The contractor registration application asks for proof of coverage from an employer who must register:
“Proof of Delaware worker’s compensation insurance.”
For a solar business the path is direct. The policy comes from an insurer the Department of Labor approves and the state authorizes to write workers’ compensation, chosen in the private market, unless the Department accepts proof that the business can pay compensation itself. The Division of Industrial Affairs, part of the Department of Labor; workers’ compensation administration, compliance and contractor registration.
How crews are classified and how subcontractors are treated at audit are policy questions rather than Delaware questions, set out on the workers’ compensation page. As advice, collect a certificate from every subcontractor before its people set foot on an array.
Delaware’s electrical license runs through a state board, and the Division of Industrial Affairs appears among the bodies listed below. For a crew working at height, OSHA’s Fall Prevention Campaign is the one to pair with that.
Delaware offices, matched to the file each keeps
The Delaware Department of Insurance is the state’s insurance regulator; the chapter refers to the Insurance Department for the licensing of workers’ compensation insurers. Any agency that sells you a policy, this agency among them, can be looked up on NIPR.com.
The other public bodies behind this page each hold a separate part of the picture. Each link goes to the body’s own site, and each role is given as the record states it:
- Board of Electrical Examiners: licenses electricians and electrical inspection agencies; its rule names solar electrical work among the work it covers
- Division of Professional Regulation: staffs the professional licensing boards, including the electrical board; its list of boards carries no solar board
- Division of Revenue: issues the contractor business license every contractor needs
- Office of Contractor Registration: registers construction contractors with the Department of Labor before they start work
- Division of Industrial Affairs: part of the Department of Labor; workers’ compensation administration, compliance and contractor registration
- Delaware Public Service Commission: utility regulator: net metering rules and the certificate to operate for community-owned energy generating facilities
- State Fire Prevention Commission: adopts the state fire prevention regulations that list the National Electrical Code edition
- State Fire Marshal: state fire code administration; announced the new edition of the fire prevention regulations
- Delaware Department of Justice, Consumer Protection Unit: enforces the Consumer Fraud Act and its Home Improvement Services Regulation for residential home improvement contracts
Not confirmed on this page: a state body that issues a solar contractor license. Absent on purpose: a state fund that insures employers. In an ordinary week the offices that matter are the Board, its inspection agencies, the Division of Revenue and the Department of Labor’s registration office.
The Delaware counties inside each metro card
The cards below show the metropolitan areas with a principal city in Delaware, as the U.S. Census Bureau delineates them, and the Delaware counties inside each.
Philadelphia-Camden-Wilmington, PA-NJ-DE-MD
Part of this metro lies outside Delaware; this card lists its Delaware counties only: New Castle County.
Dover, DE
Made up of Kent County.
As advice, log the county for every job you price and ask the local permitting office about standards stricter than the state’s before the proposal goes out.
Policy pages that answer the license, the inspection and the payroll
The findings above say where Delaware’s rules sit. The policies that answer for the work are the ones a solar business carries wherever it works, and each has its own page:
- The electrician license, the electricians you bring in and the inspection of finished wiring point to general liability, which also takes up damage to the roof or building under the array.
- Estimates and designs a customer or a community project owner relied on point to professional liability.
- The compulsory comp law and the registration application’s proof of coverage point to workers’ compensation, placed with an authorized insurer.
- Trucks and trailers that carry modules and racking between the yard and the job point to commercial auto.
- Your own gear on the way to the roof or the field points to tools and equipment.
- Contracts that ask for limits above the primary layer point to umbrella liability.
Which of those weigh heaviest depends on the work, and the pages on rooftop installation, panel cleaning and maintenance and ground-mount and solar farm construction take each kind of work on its own terms. When you are ready to put the pieces together for Delaware jobs, a quote request is the place to start.
State rules decide who may do the work and how; the policies decide who pays when something goes wrong.
- A license, registration or certification is a requirement of the state, not insurance.
A panel for Delaware in rows. Each row sets a requirement of the state beside the exposure that requirement leaves open and the coverage line that answers it. License to install: A state license reaches solar installation. It leaves open damage to the roof, the building or a neighbor’s property from the installation work, which General Liability answers. Solar sales and installer rules: The state sets its own rules for solar sellers, installers or providers. It leaves open a design, sizing or output estimate the customer relied on that turns out wrong, which Professional Liability answers. Electrical code: The state adopts the National Electrical Code statewide. It leaves open a wiring or tie-in fault traced back to the work after the job is done, which General Liability answers. Workers’ compensation: Required for covered employers, bought in the open market. It leaves open a crew member hurt on the job, which Workers’ Compensation answers. Notes: A license, registration or certification is a requirement of the state, not insurance. The conclusion reads: State rules decide who may do the work and how; the policies decide who pays when something goes wrong. No figures are shown.
Nearby states we also write
Delaware coverage, services and state offices
What we insure
Coverage lines
Outside authorities
- Delaware Department of Insurance
- Board of Electrical Examiners
- Division of Professional Regulation
- Division of Revenue
- Office of Contractor Registration
- Division of Industrial Affairs
- Delaware Public Service Commission
- State Fire Prevention Commission
- State Fire Marshal
- Delaware Department of Justice, Consumer Protection Unit
Delaware solar contractor insurance questions
The electrical chapter never uses the word solar. Does the Board’s rule still put array wiring under an electrician license?
The Board of Electrical Examiners’s rule defines electrical services and lists solar electrical work among them, while the chapter itself speaks of lighting, heating or power in any structure. The solar reach therefore rests on the rule. Settle which licensed electrician will do the wiring before you bid, and name that person in the proposal so the customer sees who answers for it.
We hold the contractor business license from the Division of Revenue. Does that alone cover a rooftop array?
No. The Division of Revenue issues the contractor business license every contractor needs, and the Department of Labor’s Office of Contractor Registration registers construction contractors, but neither is a solar credential. The wiring still needs a licensed electrician under the Board. Hold all of these together, and keep each in the job file for the permit office.
Who signs off on finished array wiring before the utility turns the system on?
A Board-licensed inspection agency issues the certificate of inspection the electrical chapter calls for, and the Board of Electrical Examiners licenses those agencies. Schedule that inspection into the job rather than treating it as an afterthought, and ask the agency what it needs on site. A finished job that cannot be connected is a costly wait for your customer and for you.
We are building a community-owned project for a developer. Does our firm need the certificate the Delaware Public Service Commission issues?
The certificate to operate belongs to the facility owner, not to a rooftop seller or an installer, and the Delaware Public Service Commission issues it. Ask the owner for evidence that the certificate, the interconnection study or agreement and proof of site control are in hand before your crew mobilizes, and put that request in your contract.
If we lease systems to customers, does Delaware require our company to register as a seller?
Not confirmed at the state level on this page. The net metering provision names customers who lease a generating facility or contract with an outside owner, and the record shows no seller duty set there. The community-facility certificate belongs to the facility owner. Have your own counsel review a leasing model before launch.
An inspector in a county we have never worked in wants a stricter wiring standard. Can that county ask for it?
The State Fire Prevention Commission’s regulation has the force and effect of law in every county, city and political subdivision, and a city or county may add stricter local standards. The Board’s rule adds that the Commission determines the version that applies to a project. Ask the permitting office what it enforces before the design is final.
The workers’ compensation chapter creates a fund. Can our solar company buy its policy from it?
No. That fund exists to reimburse insurance carriers and insures no employer. A Delaware employer either insures with a company the Department of Labor approves and the state authorizes, or proves its ability to pay directly. For a solar business that means a private-market policy placed before anyone on the payroll climbs a roof.
Before we sign with an agency for this program, what should we check about its Delaware insurance license?
The Delaware Department of Insurance regulates insurance in Delaware, and an agency’s license, ours among them, can be looked up on NIPR.com. Ask any agency quoting your program for its license details and confirm them before you sign. Because the chapter creates no fund that insures employers, your comp policy is placed with an authorized private insurer like the rest of the program.
This page describes insurance for solar contractors operating in this state. It is general information, not legal advice and not a statement of coverage. Licensing, interconnection and code requirements change; verify current requirements with the agency named before relying on them.
Get a quote for your Delaware solar contracting business
Tell us which Delaware counties you work in, who holds the electrician license on your jobs, and whether you build for community-owned projects, and we will shape a program around those answers.